Replacement for a 14,000 lbs Underslung A-Frame Trailer Coupler

Question

Question:

is there a repair kit for the a frame trailer coupler for 2 5/16. The pin holding the mechanism is worn and keeps falling out. Can if buy a new pin or one slightly larger

asked by: Duane

0

Expert Reply:

With this being such an inexpensive part there is not a repair kit offered by the manufacturer for the thumb latch components of the A-Frame Trailer Coupler item # CA-5335-B. I wish I had an option for you but if your pin is no longer functional you will need to replace the entire coupler.

expert reply by: Jerred H

0

Answer 1

Looks like you have a standard underslung thumb latch coupler like the part #CA-5335-B. The Master Lock coupler lock part #2847DAT would fit this and work well.

view full answer...

Answer 2

I pulled up a picture of your 2015 Jayco Jay Flight 27rls and the coupler looks to be an underslung coupler like the part #CA-5335-B. Which then for a lock that is specifically designed to fit this type of coupler we have the part #AT89006 from…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 6

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. The Replacement Head for Blue Ox SwayPro Weight Distribution Systems part #BXW4011 is for…

view full answer...

Answer 7

If you are just looking for a new converter, the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers part #PD4635V will be a direct upgrade for the Magnetek Converter Series 6300 Model 6332 that you have now.

view full answer...

Answer 8

There is a suspension enhancement option for your 2021 Entegra Vision XL built on a Ford F-53 chassis, but I verified with the manufacturer that the steering stabilizer only fits if you have at least a 24,000 lb GVWR. You're not out of luck…

view full answer...

Answer 9

You are correct, the #8-219-4UC3 matches your existing hub and drum assembly. I'm assuming you're referencing the difference in the grease cap when you say the grease is different. This has a standard grease cap, but you can use your existing…

view full answer...

Answer 10

To replace your Dometic Sunchaser 834AV19.401 awning fabric you will need a 19' Solera fabric replacement. I have the following color options available for you to match your trailer's aesthetics: Sand Fade w/ White Weatherstrip #LCV000334429…

view full answer...

Answer 11

We currently have three versions of the Demco 32 degree A-Frame coupler but none of them are zinc plated. We have the part #DM15633-97 which is primered, the part #DM15633-81 which is powder coated black, and we have the part #DM15633-52 which is…

view full answer...

Replacement for a 14,000 lbs Underslung A-Frame Trailer Coupler

Product Page this Question was Asked From

Continue Researching