Difference Between Prodigy P2 and Redarc Tow Pro Liberty Brake Controller 2011 Toyota Sequoia

Question

Question:

I appreciate the quick response. Will the Redarc unit come with a dash plug specific for the Sequoia? Or do I need to get it separately?

asked by: Mark

1

Helpful Expert Reply:

The braking is going to be about the exact same between the Prodigy P2 part # 90885 and the Redarc Tow Pro Liberty part # RED52VR. The main difference will be that the Redarc only puts a small know on your dash and the P2 is a traditional brake controller that is much bigger. To install either controller you'd need the install harness part # 3040-P. For how much cleaner of an install the Redarc provides that would be the route I would go with.

For tow mirrors the K-Source set part # KS81300 would be your best option. These are custom fit so the install is easy and the fit is tight plus they allow the puddle lights on the mirrors to still function.

expert reply by: Jameson C

1

Mark

9/23/2022

I appreciate the quick response. Will the Redarc unit come with a dash plug specific for the Sequoia? Or do I need to get it separately?

Reply

Jameson C.

9/23/2022

You would need to purchase that separately with part # 331-TPSI-002. I should have mentioned that earlier.

Reply

Answer 1

Bearing Buddies are a great way to keep grease in a trailer hub. I recommend them as long as you are aware that it's very easy to put too much grease in a hub with these which will blow out the seal. They have no problem being used on longer road…

view full answer...

Answer 2

It sounds like you are on the right track with everything here. You can use the Hopkins part #37185 to convert your 4-pole connector to a 7-pin connector, but this is just the adapter. We've built a complete kit for this exact situation and it…

view full answer...

Answer 3

Good Afternoon Lucas, you are on the right track for the easiest way to install a brake controller on your 2020 Subaru Outback Wagon. The Curt Echo brake controller part #C51180 is unlike any other brake controller on the market at this time…

view full answer...

Answer 4

For your 2022 Subaru Outback Wagon, you'll need to first add a 4 way trailer connector if not already equipped. I recommend the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #118467 for this. This kit includes everything you…

view full answer...

Answer 5

We have the similar brake controller install kit part #ETBC7 which comes with 25 feet of duplex wire like you mentioned. This might be long enough as you said your van is 20 feet end to end. We also have an extension wire for this with part #10-2-1…

view full answer...

Answer 6

If your vehicle is equipped with a 4-Way connector, the Curt Universal Installation Kit #C57186 that you referenced includes everything needed to convert it to a fully-functional 7-Way. This includes the needed 10 gauge wire that you will connect to…

view full answer...

Answer 7

You can absolutely use the Redarc Tow-Pro Liberty Brake Controller #RED24FR in your 2023 Subaru Outback. But you will need the Universal Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers #RED69FR for installation. There may be a few more…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Difference Between Prodigy P2 and Redarc Tow Pro Liberty Brake Controller 2011 Toyota Sequoia

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching