Recommended Coupler Lock For a 2-5/16" Trailer Coupler

Question

Question:

Hi, I’m looking for a coupler lock for a 2-5/16” ball. Do you carry one please?

asked by: Ron S

0

Expert Reply:

I prefer to use the Master Lock Universal Trailer Coupler Lock # 379DAT as it works with a wide variety of trailer ball couplers from 1-7/8" to 2-5/16". We have the Master Lock Trailer Hitch Receiver Lock and Coupler Lock Set # 3794DAT that includes this same coupler lock along with a coupler latch lock and receiver lock that are all keyed alike.

expert reply by: Bud M

0

Answer 1

We have a few options for your coupler with a 4-1/2" lip. The etrailer Trailer Coupler Lock #e98895 is a good lock. From there we move up to the better Trimax Dual Purpose Coupler Lock #TMX67FR which uses a hardened steel construction. The…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to my research, AL-KO 8490 references an AL-KO hub for 3,500 lb axles with a 10 x 2-1/4" drum and a 5 on 4-1/2" bolt pattern. For a drum assembly that will work with these hubs I recommend taking a look at the Electric Trailer…

view full answer...

Answer 5

The grease cap part number that you referenced cross references to a drive in cap with a 2.44 inch outside diameter. If you have a standard cap then the Grease Cap, 2.44 inch OD Drive In, item #RG04-060, is the correct part. If you have a grease…

view full answer...

Answer 6

The Dexter brake assembly 023-217-00 is a 10 by 2-1/4 brake for 3,500 pound axles that fits a 4-bolt brake mounting flange. For replacements I recommend part #AKEBRK-35-SA that includes both sides. They're labeld to make the install easier and…

view full answer...

Answer 7

Not confusing at all. I took a look online and the 2001 Silverado 2500HD has a 12,000 lbs bumper pull towing capacity and a 15,200 lbs 5th wheel towing capacity. It's just two different capabilities of the truck. The extra weight of a 5th wheel…

view full answer...

Answer 8

There are 4 wires coming out of the back of the Draw-Tite Activator IV Brake Controller part 5504. You are correct in that the black wire runs to the positive side of the vehicle battery through a circuit breaker. The white wire runs to the negative…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Dexter part 10-41 is a grease seal for a mobile home utility hub. It has a specified inside diameter of 1.938-inches and an outside diameter of 2.523-inches. The nearest match we offer is the Redline part #10-40 which is a single-lip seal that has…

view full answer...

Answer 11

I was able to get a dimension sheet from my contact at Curt for the Curt Hitch part #C15800 that you referenced. See attached pic. I also attached a set of the installation instructions for this hitch.

view full answer...

Answer 12

You are going to want the Master Lock Hitch Receiver and Coupler Latch Lock Set #1481DAT as it has an adjustable coupler lock which fits multiple coupler latch sizes. This like the etrailer Hitch Receiver and Coupler Lock Set #e99039 you found will…

view full answer...

Recommended Coupler Lock For a 2-5/16" Trailer Coupler

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching