Recommended 12" Electric Trailer Brakes with 4-Bolt Mounting Flange

Question

Question:

I have a 12,000 gvw trailer with a 12X2 brake drum and a 4 bolt flange on the trailer. Do you have a set of electric brakes that will fit my trailer?

asked by: Bruce S

0

Expert Reply:

Yes, we do offer brakes this size in a four bolt pattern, the Dexter Electric Brake Kit for 4 Bolt or 5 Bolt Flange part # 23-105-106-09 which measures 12" x 2" and has a 6,000 lb weight capacity.

expert reply by: Conner L

0

Answer 1

The center hole of the brake assemblies #23-105-09 and #23-106-09 measures 3-3/16 inches across. The kit for both of these is the part #23-105-106-09 that you referenced.

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 8

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Recommended 12" Electric Trailer Brakes with 4-Bolt Mounting Flange

Product Page this Question was Asked From

Continue Researching