What Is The Thickness Of Shackle Strap # 115052

Question

Question:

What is the thickness of the shackle straps? It lists all the dimensions but the thickness.

asked by: Danny E

0

Expert Reply:

The thickness of the replacement shackle strap # 115052 is 3/16 inches thick, it is 1-1/4 inches wide, 2-5/8 inches from center of hole to center of hole, and has a bolt hole diameter of 9/16 inches.

I attached a review video link below.

expert reply by: Noah E

0

Shackle Strap Measurements
(click to enlarge)

Answer 1

If you look at the photo I have edited for you, you can see all the relevant dimensions of the #115052 leaf spring shackle.

view full answer...

Answer 2

The thickness of the Replacement Shackle Strap #115208GALV is 3/16 of an inch.

view full answer...

Answer 3

My recommendation for your application is to use the Dexter Single-Axle Trailer Hanger Kit for 2-1/2" Slipper Springs - 5-1/4" Front #HAP-158-00. This can be used with the 10K GD Spring Eye Bolt w/ Grease Zerk #7-135-2 and Locknut -…

view full answer...

Answer 4

The closest suspension bolts that we have with a grease zerk fitting that are near the 4-1/4 inch length that you are looking for are 4-1/2 inches long. The Redline #7-135-2 has a 3/4 inch diameter while the Redline part #7-260-2 has a 7/8 inch…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 7

The absolute best cushioned equalizer that fits the dimensions you mentioned having would be the MORryde ALLTREK 4000 part #MR89DR as this is only option to provide vertical and horizontal cushioning. This would make a big difference and you'd be…

view full answer...

Answer 8

Yes, axle spread and wheel base by definition are the same measurements. You will measure from the center of one axle to the center of the 2nd axle to determine what you axle spread is. This may be difficult as some wheels and covers will make this…

view full answer...

Answer 9

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 10

Since Grand Design is kind enough to list certain parts for their trailers I can confirm you have a 33" wheelbase on your 2020 Grand Design Transcend 27BHS. This means the MORryde Rubber Equalizers #MR87ZR will fit your trailer. Although I'm…

view full answer...

Answer 11

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 12

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

What Is The Thickness Of Shackle Strap # 115052

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching