Is There A 6" Handle Compatible w/ Dutton Lainson DL2000A Winch?

Question

Question:

Is there a 6” handle to replace the 9 1/2 “ DL2000A? I really could use the extra clearance the 3 1/2 “ would afford. Thanks!

asked by: Bill

0

Expert Reply:

There sure is!

The 6" handle compatible with your Dutton Lainson DL2000a # DL14725 is the # DL70336. This will give you that extra clearance you are needing.

expert reply by: Samuel C

0

Answer 1

If you were looking for a replacement handle, the hole opening on the Replacement Quick Attach Winch Handle for Dutton Lainson Winch - 9-1/2" #DL70330 will measure 15/32" by 5/8" and looks like it will be a good replacement for your…

view full answer...

Answer 2

I spoke with my contact at Dutton-Lainson and she verified that the Replacement Winch Handle, #DL70336, is a Quick Attach model like shown in the pictures on the product page.

view full answer...

Answer 3

Each of the Dutton-Lainson handles you have referenced are designed as exact replacements for different winches, so the difference is what models each will fit. For the Replacement Handle #DL70328, it will fit the following models: DL1602DD…

view full answer...

Answer 4

The Replacement Winch Handle for Dutton Lainson Winch, part #DL70336 is designed to fit Dutton-Lainson winches like part #DL15502. I went to our warehouse and measured the #DL15502 shank the handle fits. The shank measures .46 X .625 inches. I have…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...