Is It Safe To Use a Receiver as a Lifting Point On a 2021 Chevrolet Equinox

Question

Question:

I am wondering if it is safe to use the hitch that I installed on my 2021 Equinox as a jacking point to lift the rear of the vehicle.

asked by: Ben

0

Expert Reply:

You should never use the Draw-Tite Max-Frame Trailer Hitch Receiver # 76419 as a lifting point for your 2021 Chevrolet Equinox. The receiver is not capable of supporting the weight of your Equinox and may easily become damaged if you used it as a lifting point.

We do offer the Performance Tool Electric Car Jack # PTW1609 that will more easily allow you to jack up your Equinox and use Jack Stands # PTW41021 to safely work under your vehicle.

expert reply by: Bud M

0

Answer 1

We have better options because leveling jacks like the Ultra-Fab #UF48-979006 shouldn't be used to raise a vehicle. They're only for stabilizing despite their weight capacity. Instead you want something like the Powerbuilt bottle…

view full answer...

Answer 2

We do have a jack that would work for you when you want to change the tire on your trailer or vehicle, but the Ultra-Fab Ultra Scissor Jack, part #UF48-979006 is not designed to be able to hold that much weight. Ultra-Fab's note states…

view full answer...

Answer 3

Since a trailer hitch ball allows for quite a bit of side to side movement as to not bind up while driving, you shouldn't have any problems using a jack such as the #ALL620470 you were looking at lifting the trailer high enough to change a…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

In order to determine if a 2020 GMC Terrain has the factory tow package you will need to take a look in the rear fuse box on the driver side of the vehicle. In the fuse box there will be two locations you need to check, K2 and K3 which are for the…

view full answer...

Answer 8

Yes the Replacement Brass Connector #T4750300 for Titan Disc Brake Actuators will fit a Tie Down 660e disc brake actuator.

view full answer...

Answer 9

We had a customer who was able to replace his Dexter 8-155 hubs with the #8-201-5UC3-EZ that you referenced so they should work well for you. You can verify that this hub will work for you by pulling your current hub and making sure they have inner…

view full answer...

Answer 10

I spoke with my contact at Lippert and the replacement motor you'll need for your Thompson Saginaw Part No. 7831293 is the Replacement 18:1 High Speed Motor Assembly for Lippert Components Venture Actuator and Slide-Out #LC295380.

view full answer...

Answer 11

To replace your AL-KO 568303 seal you will want the Oil Seal #91030. This seal has the same inner diameter of 2.750 inches and outer diameter of 3.779 inches. It is a confirmed fit for your #99 spindle that uses the AL-KO 568303 seal.

view full answer...

Answer 12

Yes, we do and I have attached it below. The etrailer Hitch item #e59ZR is confirmed to fit the 2023 Equinox. It bolts to your vehicle with included hardware. If you are planning on towing you will also need a wiring harness item #C94FR if you have…

view full answer...