Bearing Kit For Dexter 8-133 Hub

Question

Question:

Do you have wheel bearings for a dexter 8-133 hub. A kit if you do let me know the part number. Thanks

asked by: James E

0

Expert Reply:

We do have the correct bearing kit for your Dexter 8-133 hub; what you will need is the following:

- Bearing Kit # BK3-110

expert reply by: Kyle S

0

Answer 1

I spoke with my contact at Dexter regarding the axle on your trailer. This is a 6,000 pound axle that uses inner bearing #25580 and outer bearing #15123. For a complete bearing kit, you can use #BK3-100. This will include the correct inner and outer…

view full answer...

Answer 2

For a Dexter 6,000 lb axle the correct bearing kit with grease seal would be the #BK3-110.

view full answer...

Answer 3

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 6

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 9

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 10

I understand your worry Tom, and I have a couple recommendations. First is the MORryde ALLTREK 4000 Shock Absorbing Equalizers #MR89DR which has a height of 4-1/2" for the mounting bolts. This is also 6-1/2" in width like the shorter…

view full answer...

Answer 11

The inner diameters of the LM67048 and 15123 both are the same (1.250 inches). That means that a hub with either bearing in the outer bearing would fit your spindle. The part #AKHD-655-6-EZ-K would fit your axle.

view full answer...

Answer 12

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Bearing Kit For Dexter 8-133 Hub

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching