Will Brophy Clamp On Camper Tie-Downs Work On a 2018 Chevy Silverado 3500 Dually

Question

Question:

It looks like these tie downs will work on my truck 2018 Chevy 3500 Dually with a spray in bed liner, based on previous replies. I am just confirming that they will work? This will be a temporary use while we shop and purchase a camper. Planning on a custom bed with a permanent tie down later.

asked by: Kraig J

0

Expert Reply:

I do have an option for you but the Brophy Clamp On Camper Tie-Downs aren't recommend for dually models per Brophy, they can sometimes work but we don't have fit details on exact year/make/models. The best option we could offer for a confirmed fit is the HappiJac Truck-Mounted Camper Tie-Downs part # LC350763-182971. These would then require the HappiJac Original Turnbuckles for Camper Tie-Downs part # LC182898.

expert reply by: Conner L

0

Answer 1

Thanks for the picture! I would definitely go with one of the HD kits over the 2,000 lbs RoadActive item #RAS3611 you were looking at. Which one you will need is going to depend on whether or not your 2020 Chevy Silverado 2500HD has the factory…

view full answer...

Answer 2

I would not recommend the part #RAS3611-HD for your 2017 Nissan Titan XD. This kit is designed for heavier duty vehicles so it would make your suspension harsh. The part #RAS3611 is the correct kit you'd want. It will give you the…

view full answer...

Answer 3

We measured the TorkLift StableLoad #TLA7310S and found that from the center of the mounting hole to the furthest edge is 3-5/8 inches on one side, and 2-1/8 inches on the other side. To determine if the StableLoad will clear your Quadrasteer…

view full answer...

Answer 4

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 5

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

I spoke with my contact at Pollak and he stated that the Pollak Replacement 7-Pole, RV-Style Trailer Connector Socket, #PK11893-11933 is the correct replacement part for the Pollak PA66-MD40 that you have.

view full answer...

Will Brophy Clamp On Camper Tie-Downs Work On a 2018 Chevy Silverado 3500 Dually

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching