Correct Replacement Idler Hub and Bearing Kit for CE Smith Multi Sport Trailer CE48810

Question

Question:

Hi, Own a CE Smith multisport Boat trailer # CE48810 , I need to know the HUB BEARING KIT , to replace the both tires .... Thanks a lot for you help.... regards

asked by: Horace C

0

Expert Reply:

The correct replacement idler hub for the CE Smith Multi Sport Boat and Kayak Trailer part # CE48810 is the CE Smith Trailer Hub Assembly part # CE13210 or if you are just looking for a bearing kit it's the Bearing Kit with Grease Cap part # DL21792.

expert reply by: Conner L

0

Answer 1

The correct replacement hub for the CE Smith Multi Sport Trailers like part #CE48870 is the CE Smith Trailer Hub Assembly part #CE13311.

view full answer...

Answer 2

Thanks for the photo! Using the VIN I was able to gather the necessary information needed to help you find the correct idler hubs. For this, I recommend the CE Smith Trailer Hub Assembly part #CE13311. This hub uses a L44649 inner/outer bearing,…

view full answer...

Answer 3

There are a couple schools of thought on the use of EZ lube spindles for putting grease in hubs. I personally wouldn't pump them full of grease until the old grease pushes out as I'd be afraid to blow out the seals. Since this is a…

view full answer...

Answer 4

That's not a number we are familiar with. What's the inner diameter of the bearing? If it's 1 inch most likely you have a L44643 and the 6 just happens to look like a 5.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 8

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Correct Replacement Idler Hub and Bearing Kit for CE Smith Multi Sport Trailer CE48810

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching