Upgrading A and E Manual Awning of 2006 Sierra to 12 Volt Power Awning

Question

Question:

I have a 2006 serria fifthwheel with a AandE 18 manual awning. I am thinking of converting it to 12 volt electric, is this possible and what kit would you recomend? Thanks

asked by: Darryl P

0

Expert Reply:

Yes you can convert your A and E manual awning to a 12 volt power awning with the Solera 12V Power RV Awning Conversion Kit # LC434724 that you referenced. This comes with everything needed to make the conversion and is perfectly compatible with your current awning and roller.

expert reply by: Jameson C

0

Answer 1

To get power to the controller of your Solera Smart Arm 12V Power RV Awning part #LC759404, you need to tap into an existing circuit, or run a power wire from the battery with an inline fuse holder, and a 15 amp fuse, like part #SWC9538, and part…

view full answer...

Answer 2

To convert your Dometic manual awning to a power unit, you can use the Solera 12V Conversion Kit in Black #LC434723 or White #LC434724 if you have a manual crank system. These Solera kits are compatible with Dometic (A&E) awnings like what you…

view full answer...

Answer 3

I attached a wiring diagram for the Solera Power Awning Switch Kit #LC285500 for you to check out.

view full answer...

Answer 4

Some awnings have adjustments that will make the arms different lengths. This is for water run off and or to get the shade where you would like it. It seems like you have an awning like that. The Solera Awning #LC434724 has three sets of holes that…

view full answer...

Answer 5

I checked with the manufacturer for you, and they say that the Solera Awnings are slower when they retract. If you are sure there are 12 volts by testing with a multimeter the next thing to do is ensure the pitch arms aren't bent at all, which…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...

Upgrading A and E Manual Awning of 2006 Sierra to 12 Volt Power Awning

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching