Switch Wiring Diagram for Solera Power Awning Switch Kit # LC285500

Question

Question:

After 3 week back order I received the inside awning switch. I need help with wiring the new switch to the existing switch. Inside switch has red, white, blue and black color wires. The existing switch LC644584 has red, black, white and a white with red strip. I need to know the color connections and still be able to charge the battery. A diagram would be a great help. Im leaving on a 30 day trip in10 days I would love to have the new switch installed and working. Thanks in advance for your assistance.

asked by: Don J

0

Expert Reply:

I attached a wiring diagram for the Solera Power Awning Switch Kit # LC285500 for you to check out.

expert reply by: Jameson C

0

switch diagram
(click to enlarge)

Answer 1

To get power to the controller of your Solera Smart Arm 12V Power RV Awning part #LC759404, you need to tap into an existing circuit, or run a power wire from the battery with an inline fuse holder, and a 15 amp fuse, like part #SWC9538, and part…

view full answer...

Answer 2

I attached a picture of the wiring diagram for the Solera Smart Arm 12V Power RV Awning Conversion Kit #LC759404 that you referenced.

view full answer...

Answer 3

I attached a diagram that shows how the Atwood switch part #AT91959 wires up. There are three sets of wiring diagrams that you will need to compare to the water heater you have now to determine which is correct.

view full answer...

Answer 4

The Global Link Locking Slam Latch #295-000078 is designed for doors 1-3/4" thick and the #295-000015 is designed for 1-1/2" thick, so you would need to know how thick your pass thru doors are in order to choose the correct one. With that…

view full answer...

Answer 5

To convert your Dometic manual awning to a power unit, you can use the Solera 12V Conversion Kit in Black #LC434723 or White #LC434724 if you have a manual crank system. These Solera kits are compatible with Dometic (A&E) awnings like what you…

view full answer...

Answer 6

Thanks for the info you listed. Based on that the correct replacement motor is the part #LC295380.

view full answer...

Answer 7

I went out to our warehouse to take a few measurements on both the clamp and mounting plate for the Inno Velo Gripper Bike Rack #INRT201. The black plate measures 4 inches long and 2-3/8 inches wide with a small lip that measures 1 inch wide. The bed…

view full answer...

Answer 8

Using wheel covers is a good idea when your motorhome is in storage or sitting in the sun for an extended period of time. Single wheel covers fit over the outside wheel but they don't fit over the inside wheel due to the wheels being bolted…

view full answer...

Answer 9

The Solera Power Awning Switch Kit #LC285500 does have 6 pins on the back of it, the included harness just has two internal jumper wires running between a few of the pins making it so there are only four wires. Since your switch has 6 individual…

view full answer...

Answer 10

There is an option to add a wind sensor to the Solera Smart Arm 12V Power RV Awning - 16' Wide - Programmable - Black Fade #LC517486. All you need for this is the Wind Sensor for Solera Smart Arm 12V Power RV Awnings #LC715123. The only other…

view full answer...

Answer 11

There should be no issue wiring a separate switch on the outside of your trailer. However, there won't be a way to do this without hardwiring the #LC285500 into your current switch. I should also mention that this isn't typically used…

view full answer...

Answer 12

I checked with Lippert and here are the transmission fluids they recommend for the Level Up system if the temperatures will be above freezing and also what would have came with it. Dexron III/Mercon® ATF Mercon V ATF Dexron VI ATF PetroBlend…

view full answer...

Switch Wiring Diagram for Solera Power Awning Switch Kit # LC285500

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching