Recommended Axle Kit For A Boat Trailer With A 48 Inch Hub Face
Question:
I need for an axle kit for a small trailer with a 48 inch hub face and 38 3/4 inch spring center? I need an axle kit for this. Do you have one? Thanks!
asked by: Bud
Expert Reply:
When it comes replacing the trailer axle on your boat trailer that has a 48 inch hub face I would recommend The Timbren Axle-Less Trailer Suspension System - Straight Spindle Only - 3,500 pounds # ASR3500S05.
This axle-less system provides a smooth, quiet, safe ride and can eliminate the need for an axle, which allows for maximum ground clearance and a low deck height. This system will fit any frame width. This kit has a heavy-duty steel construction that has a black powder coat finish that resists wear and corrosion. It is easy to install and align. You can either bolt or weld to your trailer's frame.
This system it meant for a 1-axle or 2-axle trailer and is not recommended for triple-axle applications. The hubs needed for the kit need to have an inner bearing # L68149 and an outer bearing # L44649.
The Timbren Axle-Less suspension system may require additional support on your trailer. If your trailer does not have a crossmember above the spot where you want to install the Timbren system, then you may need to reinforce the frame on your trailer. You can do this three different ways:
-You can retrofit the trailer with a crossmember
-You can build out the trailer frame
-You can use a standard, 2-inch steel tubing to connect the 2 Timbren suspensions together using the built-in square hole on each unit.
I attached a review video link below.
Products Referenced in This Question
Timbren Axle-Less Trailer Suspension - Standard Duty - No Drop - 4 Bolt Flange - 3,500 lbs
- Trailer Axles
- Rubber Spring Suspension
- Easy Lube Spindles
- No Hubs
- 3500 lbs
- Spindles Only
- Universal Fit
- No Drop or Lift
- Timbren
more information >
Replacement Trailer Hub Bearing - L44649
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.063 Inch I.D.
- Bearing L44649
- Race L44610
- 3500 lbs Axle
- etrailer
more information >
Replacement Trailer Hub Bearing - L68149
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.378 Inch I.D.
- Bearing L68149
- Race L68111
- 3500 lbs Axle
- etrailer
more information >
Product Page this Question was Asked From
Dexter Trailer Idler Axle w/ Hubs - EZ-Lube - 5 on 4-1/2 Bolt Pattern - 60" Long - 2,200 lbs
- Trailer Axles
- Leaf Spring Suspension
- Easy Lube Spindles
- Idler Hubs
- 2200 lbs
- 5 on 4-1/2 Inch
- 48 Inch Long
- 60 Inch Long
- No Drop or Lift
- Dexter
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Upgraded Trailer Axle Solution for 4x8 Harbor Freight Trailer
- Q&A: Upgrading Trailer Tires and Wheels For Highway use on Harbor Freight 4x8 Folding Trailer
- Q&A: Will ST175/80R13 Trailer Tires Fit on the Harbor Freight Super Duty Folding Trailer?
- Q&A: Axle Upgrade for my Harbor Freight 1720 Utility Trailer
- Q&A: Replacement 2,200-lb Axle Kit For A Small Utility Trailer
- Q&A: Is a 2001 Ford Explorer Sport Trac Pre-Wired for a Brake Controller
- Q&A: Upgrading the Tire and Wheel on a Harbor Freight Trailer
- Article: Trailer Tire Sizing
- Article: How to Replace Trailer Leaf Springs in 5 Steps
- Article: How to Tell the Weight Rating of a Trailer Axle
- Article: Where to Position the Trailer Axle?
- Article: 7 Common Questions Everyone Has About Trailer Tires
- Article: Best Camper Jacks
- Article: Best Landing Gear