Troubleshooting A Loose Slide Out Motor Mounting Screw
Question:
the 12vdc motor is attached to the gear head aluminum housing with two #8 fine thread screws. the motor works ok, but the top screw hole has stripped threads and the screw wont grip. the motor then tilts downward and the gears dont mesh, so the drive shaft doesnt rotate. I used a 4inch C-clamp from my trucks toolbox in place of the bad screw to hold the motor tight to the housing, and the operator worked great. Can I bore a 5/32inch hole through the stripped hole, all the way through the housing, coming out through the galvanized sheet metal back plate? If so, then I can use a long bolt to attach the motor to the housing. thank you,
asked by: Thomas G
Expert Reply:
There is a gear in the housing of the Replacement 18:1 Venture Motor and Driveshaft with Right Angle Gear Box # LC117292 right by where you would bore through so you run the risk of it interfering with the operation of the motor.
You'd also break through without a gasket to seal up the housing so the internal components could be compromised by the elements. You'd also be voiding any warranty you have with the manufacturer so I can't recommend this route.
You can replace just the motor with part # LC295380, which would solve your issue without voiding any warranties or taking any risk.
Products Referenced in This Question
Replacement 18:1 High Speed Motor Assembly for Lippert Components Venture Actuator and Slide-Out
- RV Slide Out Parts
- Motor Parts
- Motor
- Lippert Venture Slide-Out Systems
- Lippert
more information >
Product Page this Question was Asked From
Replacement 18:1 Venture Motor and Driveshaft with Right Angle Gear Box
- RV Slide Out Parts
- Motor Parts
- Motor
- Lippert Above-Floor Slide-Out Systems
- Lippert
more information >
Continue Researching
- Shop: Replacement 18:1 High Speed Motor Assembly for Lippert Components Venture Actuator and Slide-Out
- Shop: Replacement 58:1 High Speed Motor Assembly for Lippert Venture Slide-Out
- Search Results: slide out motor
- Video: Review of Lippert Components RV Exterior - LC295380
- Q&A: Replacement Motor for Slide Out Motor with Part # 8532-18HT
- Shop: Lippert RV Slide-Out Motor by Klauber
- Shop: Replacement PowerGear RV Above Floor Slide-Out Motor - Double Shaft - Mid Torque
- Shop: Replacement Gear Motor Assembly for Lippert Slide-Out
- Shop: Lippert Venture RV Slide-Out Actuator - 40" Stroke Length
- Shop: Replacement 386480 Motor Assembly for Lippert Electric RV Slide-Out
- Video: Review of Lippert RV Slide Out Parts - RV Slide Out Standard Gear Pack Assembly - LC122837
- Search Results: slide assembly parts
- Video: Review of Lippert Components RV Exterior Parts - Replacement High Speed Slide-Out Motor - LC167098
- Video: Review of Lippert RV Slide Out Parts - Head Parts - LC74AF
- Video: Review of Lippert RV Slide Out Parts - Replacement Gear Motor Assembly - LC67FR
- Q&A: What is the Warranty on the Lippert Replacement 18:1 High Speed Motor 295380
- Q&A: Solution for Needing Replacement Gear Box for Motor/Gear Box # 7828696
- Q&A: Rebuilding Gear Motor for Lippert Power Gear Slide Outs
- Q&A: Can Motor for Lippert Components Venture Actuator and Slide-Out Be Purchased Seperate
- Q&A: Replacement Gear Option For Lippert Slide Out
- Q&A: Replacement 168956 Slide-Out Motor For A Keystone Arcadia 5th Wheel Trailer
- Search Results: yakima overhaul
- Article: Best Boat Accessories
- Shop: Fifth Wheel Hitch
- Search Results: slideout seals
- Article: How to Measure for Travel Trailer and Fifth Wheel Steps
- Shop: Suspension Enhancement
- Article: Trailer Wiring Diagrams
- Search Results: awning
- Video: etrailer Landing Gear Set Review