What Do I Need For A BedSlide Bed Tray To Fit My 2020 Chevrolet Silverado 1500 W/ Decked Drawers

Question

Question:

Would the bed slide cargo 1000# for $1100. Work with the Decked drawer system?

asked by: Jack

0

Expert Reply:

If your 2020 Chevrolet Silverado 1500 has a decked drawer system, you will need an additional part to install a BedSlide. It appears you have the 6-1/2 foot truck bed, so you will need the BedSlide Sliding Truck Bed Tray w/ T-Tracks - 1,000 lbs, part # BE36WR. In addition, you will need the Decked Installation Kit for BedSlide S and Classic Truck Bed Trays, part # BE56WR.

I have included a product description link and a video review link below.

expert reply by: Mark Smith

0

Answer 1

The BedSlide Max Extension HDTruck Bed Tray w/ T-Tracks #BE53AV is black in color. This has a 2,000lb weight capacity and has 100% extension allowing you to easily access the entire sliding tray. The included installation hardware allows you to…

view full answer...

Answer 2

If you are going to install two of the MORryde X-Factor Crossmembers #MR33WR on your tandem axle trailer Alan you would want to install them on the front and rear hangers. You can install a third one if you want on the middle hanger as well for…

view full answer...

Answer 3

There is a difference between a 7-way round and and 7-way rv blade connector. If you take a look at the accompanying photo, which is from our linked article on trailer wiring you can see that the connector on the left has blade-style pins while the…

view full answer...

Answer 4

Thanks for the pictures! Since your 2022 Grand Design Reflection 303RLS came with the CRE3000 equalizers you will need three of the MORryde X-Factor Crossmember item #MR33WR. It looks like you have the standard 3" wide frame hanger so all of the…

view full answer...

Answer 5

The recommended minimum clearance between gooseneck trailer overhang and truck bed rails is 4-6 inches. I'd recommend 6 inches but a lot of people get by with just 4. Ideally you have at least 6 inches of clearance and the trailer is sitting…

view full answer...

Answer 6

You can use that upper hole on your hanger to install the #MR33WR. Make sure you don't tighten it down too much or you will pinch the leaf spring and it won't function properly. You will also need to make sure you have enough room to install…

view full answer...

Answer 7

Yes, anytime you use a hitch extender or reducer like #HR26 you will lose about 1/3 of your hitches overall capacity. However, since you'll be towing a trailer that weighs between 4,500 to 5,000 lbs, the Brophy Hitch Reducer #HR26 will still work…

view full answer...

Answer 8

It sounds like you have a 7-way blade connector on your boat trailer as that is a very common connector on boat styles. This connector has 6 pins around the outside of the connector and a center pin for a total of 7. Part #A7WCB would be what a 7-way…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

The Timbren Trailer Suspension Enhancement System for Underslung Axles #T92MR is 5-1/4" tall. Timbren recommends The spring be in constant contact with the frame at all times. So ideally you will want exactly 5-1/4" from your axle tube to…

view full answer...

What Do I Need For A BedSlide Bed Tray To Fit My 2020 Chevrolet Silverado 1500 W/ Decked Drawers

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching