Coupler For 2" Trailer Channel That Connects to a 2" Hitch Ball

Question

Question:

I need to change the coupler on my trailer. It has a 2 channel. I would like to put a Bulldog on it, but the only thing I see in the Bulldog brand fits a 3 channel. Does Bulldog make one that will fit a 2 or is there a way to adapt the 3 to fit a 2 channel? I need one that will fit a 2 ball. Thanks for any help you can provide.

asked by: Barb M

0

Expert Reply:

The etrailer Channel Tongue Trailer Coupler # CT-3001-Z and Curt QuickPin No-Latch Trailer Coupler # C82CR are currently the only 2" ball couplers we carry that fit a 2" square trailer channel.

Bulldog's smallest coupler only fits a 3" channel.

expert reply by: Bud M

0

Answer 1

Yes, you can remove your weld-on coupler and install a new bolt-on coupler that fits a 2 inch ball. There is just a few things you need to do to before and when installing. You need to know what channel size and the weight capacity you will need for…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The Class II Curt Hitch #C12136 and Class II Draw-Tite Hitch #36493 for your 2016 Subaru Outback Wagon are very similar, but every Class I and Class II and some Class III Curt Hitches require stabilizing straps to be used when towing non trailer…

view full answer...

Answer 4

The etrailer Magnetic Hitch Receiver Reducer Sleeve #e28JR is indeed magnetic. Now the whole thing is not magnetic, there are simply two magnets built in to the bottom of the adapter. See the picture below. We chose to add magnets as a…

view full answer...

Answer 5

I can certainly point you in the right direction. Switching from hydraulic drum brakes over to EOH disc brakes is basically going to require a full conversion kit. It may be possible to re-use some of the old brake lines, but if you are doing a full…

view full answer...

Answer 6

After speaking with EZ Loader what you have on your trailer is a 3,700 lb axle. From what they said the axle was upgraded even though your overall trailer capacity is 3,100 lbs. Although this uses the same #L44649 outer and #L68149 inner bearings,…

view full answer...

Answer 7

Yes! We have both a hitch and wiring for your 2024 Toyota Grand Highlander. Hitch - Curt Trailer Hitch Receiver #C26VV Wiring - #C59236 If you are planning to do any towing, you can add the etrailer Ball Mount Kit #989900 to round out a tow package.

view full answer...

Answer 8

Hey Dave, what you gave me is enough info to get you replacement bearings. The grease seal 471750 matches the part #TMK48ZR. For a Timken replacement for the L44610 part number you'd need #TMK63VR. Then for a bearing for the L44649 you'd want…

view full answer...

Answer 9

Yes, everything you have listed will fit your 2006 Ford Freestyle. The hitch, #C12242, fits the vehicle, the ball mount, #C45572, fits the hitch, and the wiring #C55587 is a fit for the vehicle as well. You did a fantastic job getting it all picked…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

You're correct. The repalcement for your existing B12EA-22 brake would be #AKEBRK-7R-SA for the right side and #AKEBRK-7L-SA for the left.

view full answer...

Coupler For 2" Trailer Channel That Connects to a 2" Hitch Ball

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching