What is the Estimated Installation Time for Timbren Springs on a 2008 Ford F-350

Question

Question:

How long can we expect to spend installing the front and rear kits??

asked by: Dave

0

Expert Reply:

Both the front Timbren kit # TFF350SDC and rear kit # TFR350SDF can be installed in about an hour per kit. It will help to have someone helping. These kits are fairly straight forward to install. I have included a link to the installation instructions for each kit for you. Installation times can change based on the installers level of ability and whether or not all of the tools needed are readily available. I have included a link to our FAQ article on Timbren springs for you.

expert reply by: Michael H

0

Answer 1

According to my SuperSprings representative, the 1 inch increase in ride height provided by the block won't do much to change the effectiveness of the #SSR-610-47 Solo Custom Helper Springs. As you can see in the photo I've provided, The…

view full answer...

Answer 2

This will depend on how much support is needed when you are towing. That being said, however, as you do not tow too much, I recommend going with the blue SumoSprings #SSR-610-40. This will still add up to 1,000 pounds of support, but will affect the…

view full answer...

Answer 3

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 4

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 5

If you are considering Timbrens like the #TDR1500DQ and the SumoSprings like the #SSR-307-47 for your 2022 Ram 1500 4x4, I recommend the SumoSprings #SSR-307-47. The SumoSprings will offer the same quality as the Timbrens in terms of suspension…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is comfortability when you…

view full answer...

Answer 8

Hey Michael, thanks for reaching out! The Timbren Active Off-Road Bumpstops #T28GR you installed on your 2018 Ford F-150 unfortunately have that reputation among users (although Timbren claims their systems provide a smooth ride). Because of this we…

view full answer...

Answer 9

Here is a list of the bump stop replacements we have which fit your 2024 Ford F-350. If you can tell me how you plan to use your F-350 I can give you my personal recommendation for the option which works best for you. Timbren Front 2WD #TFF350SD2 4WD…

view full answer...

Answer 10

According to RoadActive Suspension the spring rate for the standard kit #RAS3611-S is 2,400 lbs. For the heavy duty #RAS3611-SHD it is 3,600 lbs. The heavy duty #RAS3611-SLHD is the same but only designed to fit if you have factory top overload…

view full answer...

Answer 11

I highly recommend going with the Air Lift LoadLifter 5000 Air Helper Springs #AL49DQ over their Ride Control system for your 2023 Toyota Tacoma 4WD because they not only offer more support, but they also have a better construction so they'll…

view full answer...

What is the Estimated Installation Time for Timbren Springs on a 2008 Ford F-350

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching