Weight of Lippert Underchassis Double Bin Storage Unit for RVs

Question

Question:

What is the weight of this product?

asked by: Mark

0

Expert Reply:

The Lippert Underchassis Double Bin Storage Unit for RVs part # LC236558 weighs around 70 lbs.

expert reply by: Conner L

0

Answer 1

The Lippert Underchassis Double Bin Storage Unit for RVs - 99-1/2" Long #LC236558 has a difference of 1-1/4 inches between the top of the bin and the mounts. So you would need to add some spacers to give you the 2-2.5 inches you need to clear…

view full answer...

Answer 2

I have a solution for you on this, and the reason you're having so much trouble finding these racks is that they're not very common because of the amount of motion that occurs on the back end of a 5th wheel trailer. Racks that are rated for…

view full answer...

Answer 3

The Lippert Underchassis Double Bin Storage Unit for RVs - 99-1/2" Long #LC236558 has a 68-3/4" measurement between the inside of the frame brackets and 70-1/2" center to center measurement of the bolt holes on the top of the bracket.…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 6

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 12

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...

Weight of Lippert Underchassis Double Bin Storage Unit for RVs

Product Page this Question was Asked From

Continue Researching