Can the Snap Pad Jack Pad Be Used on a Travel Trailer Tongue Jack

Question

Question:

Can this item be used on the tongue jack of my travel trailer?

asked by: Daniel M

1

Helpful Expert Reply:

Yes, you can use the Snap Pad Jack Pad # SN97FR on your travel trailer tongue jack as long as it will fit. The Snap Pad Jack Pad # SN97FR fits a 5-1/2" round jack foot.

expert reply by: Scott S

1

Answer 1

The Pure Power Blue Treatment for RV Holding Tanks, #V23128, is a chemical-free, biodegradable treatment that prevents odors and clogs by breaking down waste in your RV's waste tanks. Add at an equivalent of one ounces per 20-gallons of holding…

view full answer...

Answer 2

The inner lip of the Snap Pad Jack Pad for Camper Jacks w/ 5-1/2" Round Feet #SN97FR that grips onto the jack foot has a 5-1/8" measurement from one edge to the other so you'd have a bit more than 1/8" of the lip covering the jack…

view full answer...

Answer 3

We don't have a database that tells us what will fit on which coach, so you'll want to measure to confirm fitment. For example, if you have 8" round feet, select the #SP34FR4. If you have 10" round feet, you will want to select the…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Can the Snap Pad Jack Pad Be Used on a Travel Trailer Tongue Jack

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching