Yakima Roof Rack and Bike Rack Recommendation for Tracks on a Pop-Up Camper

Question

Question:

Hello, We bought a used popup camper that has an old Yakima roof rack on rails. We are looking to replace to old roof rack with a newer rack along with two bike racks. We were looking at the Thule ProRide XT bike rack but are unsure about which roof rack to buy. What we are looking for are is a roof rack that would mount to the existing rail and also fit the two bike racks. Ive attached a couple of pictures showing what we currently have. Do you have any suggestions? Thanks

asked by: Jason L

0

Expert Reply:

From the looks of your photos, you have the Yakima Round Crossbars like the # Y00411 along with the old Control Towers # Y8890027.

If you are looking for a newer model of crossbars that have a more aerodynamic design that fit into the tracks, I recommend the following setup:

- Yakima JetStream Crossbars - 70" # Y00427
- Yakima SkyLine Towers # Y53TR
- 2 sets of the Landing Pad 1 # Y00221
- Same-Key Locks # Y07204

With this setup, the JestStream crossbars create a much quieter ride and increase fuel efficiency due to the design. In order to make sure the JetStream crossbars are long enough, I recommend measuring your tracks to make sure they are no more than 70" apart.

As far as the Thule ProRide XT # TH598004, this is a great choice. Not only does the rack clamp onto the JetStream crossbars, it also is thin enough to mount two bike racks on your crossbars. The ProRide is compatible with wheel diameters up to 29" around and wheelbases up to 47-1/4". Although, it will accept some wheelbases that are between 49-3/16" - 51-3/16" depending on the frame style. It also accepts standard tires up to 3" wide.

I went ahead and attached demonstration videos for you to check out.

expert reply by: Bob C

0

Neighbor's Current Tracks and Yakima Roof Rack on Pop-Up Camper
(click to enlarge)

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 3

Really it's going to boil down to which spindle type your Bayliner Capri has. The Easy Grease Trailer Idler Hub Assembly for 3.5K Axles #AKIHUB-545-35-G-EZ-K will work with 3,500-lb Dexter E-Z Lube and etrailer Easy Grease trailer axles with #84…

view full answer...

Answer 4

Thank you for all of the information regarding your towing setup. While we do have suspension enhancement for your 2017 Nissan Titan, you are going to see the most direct benefit by ensuring that your trailer has a tongue weight (TW) that is 10-15%…

view full answer...

Answer 5

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 6

I have attached a dimensional photo of the etrailer E-Track Backing Plates part #e96RR which you can then use to determine compatibility with the Mytee Products e-Track. That said, as we do not carry this product, we cannot confirm fit…

view full answer...

Answer 7

E-tracks are typically the stronger of the two, but X-track is more versatile since you can mount them horizontally or vertically. Choosing between the two really depends upon how you plan to use them. If you are installing something in a truck bed,…

view full answer...

Answer 8

We have exactly what you need with the Easy Grease Trailer Idler Hub Assembly for 2K Axles #AKIHUB-545-2-G-EZ-2K. This has the 5 on 4-1/2" bolt pattern, uses L44649 inner and outer bearings, and a grease seal with a 1.50" inner diameter.…

view full answer...

Answer 9

I reached out to the manufacturer, Curt, who told me the Curt 7-Way Trailer Plug Extension #C86DR used 14 gauge wire.

view full answer...

Yakima Roof Rack and Bike Rack Recommendation for Tracks on a Pop-Up Camper

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching