What Is The Operating Voltage Of The Fan-Tastic 12V Roof Vent?

Question

Question:

what is the recommended voltage range?

asked by: ANDREW B

0

Expert Reply:

The Fan-Tastic Vent Roof Vent w/ 12V Fan and Thermostat # FV802250 has a recommended voltage range of 12 volts.

This roof vent will fit roofs up to 4" thick, a variable speed fan with two modes, and a simple installation that features a two-wire design.

expert reply by: Bryce D

0

Answer 1

I went to the warehouse and checked out the Fan-Tastic Vent Roof Vent w/ 12V Fan, part #FV802250. The fan motor on the vent has a 3-amp draw. This fan is designed to fit roofs that are up to 4-inches thick and the rough opening size you need for this…

view full answer...

Answer 2

In the highest speed setting the fan of the Fan-Tastic roof vent part #FV802250 that you referenced will draw 3 amps. 3 amps is 36 watts.

view full answer...

Answer 3

I do have an option for you but you can't simply replace the insides of a roof vent fan with parts from another manufacturer, they aren't standardized like this. If you're interested in Fansatic Vent, I recommend the Fan-Tastic Vent Roof…

view full answer...

Answer 4

I have some good news for your wallet because I reached out to the manufacturer, Dometic, who told me you can upgrade your 2250 Series Fan-Tastic Vent Roof Vent #FV802250 with the Fan-Tastic Vent Roof Vent Assembly Upgrade Kit #FV807357 to get the…

view full answer...

Answer 5

The Fan-Tastic Vent Roof Vent w/ 12V Fan and Remote part #FV807350 is a complete assembly that will completely replace an existing vent. The Fan-Tastic Vent Roof Vent Assembly Upgrade Kit part #FV807357 is designed as an add on to existing vents. The…

view full answer...

Answer 6

We do carry the Fan-Tastic Vent 7350 Series Upgrade Kit #FV807359 that you are looking for! It was temporarily deactivated but we confirmed it is a good part number and still supported by Fan-Tastic Vent in part thanks to your question!

view full answer...

Answer 7

The big difference is the corners of the main panel of the #FV807357 are cut out with small section to allow access to mounting hardware and the #FV807359 instead does not have this area cut out. So you'd want to look at your vents to see if you…

view full answer...

Answer 8

I do have a simple wiring diagram for the Progressive Dynamics Inteli-Power RV Converter and Smart Battery Charger - 12V - 45 Amps #PD9245C. Basically you just need to run the power wire from the converter directly to the DC distribution panel and…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

What Is The Operating Voltage Of The Fan-Tastic 12V Roof Vent?

Product Page this Question was Asked From

Continue Researching