Recommended Trailer Hitch For A 2017 Volvo V60 T6 R
Question:
Hi, I would like to put a trailer hitch on a 2017 V60 T6 R. Will it scrape if I put a frame trailer hitch receiverinch on the car without raising the suspension? The 2017 V60 R design clearance is 5.4 The 2017 V60 Cross Country design clearance is 7.9 The product in question is the: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2 Item # 75916 How low does the frame go? thanks so much for your attention on this matter.
asked by: Tim B
Helpful Expert Reply:
When it comes to installing The Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2 inch # 75916 on your 2017 Volvo V60 T6 R the hitch is confirmed to fit your vehicle and will not scrape when in use. There is a possibility it will scrape if you're going up a steep incline depending on how steep it is.
The trailer hitch has an easy, bolt-on installation that requires no welding, and has a black powder coat finish theat covers the e-coat base for superior rust protection.
The T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56287 has a simple plug and play installation that plugs into your vehicle's wiring harness, which is located inside your trunk, behind the tail lights on both the driver's side and passenger's side. Using this harness will allow your trailer's taillights to mirror the vehicle's taillights.
To finish your towing experience The Curt Starter Towing Kit # C45534 includes the ball mount, the 2 inch hitch ball and other starter towing accessories that will make your experience better.
I have attached an installation video link below.
Products Referenced in This Question
Curt Towing Starter Kit for 2" Hitches - 2" Ball - 3/4" Rise, 2" Drop - 7.5K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 2 Inch Ball
- One Ball
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 0 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- CURT
more information >
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 2 Inch Hitch
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Trailer Wiring Diagrams
- Article: Routing the Power Wire for a Trailer Wiring Harness
- Q&A: Comparing Curt And Hopkins Wiring Harnesses For 2011 Volvo XC70
- Q&A: Supercharged 2015 Land Rover Range Rover Trailer Hitch Receiver Recommendation
- Q&A: Differences Between Kuat Sherpa 2.0 and NV 2.0 Bike Racks
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Q&A: Hidden Trailer Hitch For 2022 Land Rover Range Rover
- Article: How to Choose the Right Trailer Hitch Class
- Article: My Trailer Hitch Doesn't Fit
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Q&A: Replacement Key for Volvo Rooftop Cargo Box With N122 Key
- Q&A: Trailer Hitch that Fits 2020 Volvo V60 Cross Country Wagon
- Article: How to Measure for Trailer Hitch Drop
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)