Additional Tee Required To Use Firestone Coil-Rite Air Helper Springs With Single Schrader Valve

Question

Question:

coil-rite air helper springs for chevy tahoe. In photo it shows a brass TEE coupler. Yet in kit photos it does not. It shows two separate Schrader valves. I prefer the TEE. Can I get it in the kit? Thanks

asked by: Vince

0

Expert Reply:

The Firestone Union Tee for 1/4" Tubing # F3025-1 is separate from the Firestone Coil-Rite Air Helper Springs # F4108 for your 2004 Chevrolet Tahoe. You can add the Tee to your order so that you will be able to have your air helper springs share the same single Schrader valve fill.

expert reply by: Bud M

0

Answer 1

For your 2004 Ford Crown Victoria, the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" #13707 is a great option to get you started. Then you will need to get a weight distribution system like #FA92-00-0800 for your trailer to allow…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

On the Dutton-Lainson winch #DL14881, the maximum drum capacity for a cable is 3/8 inches in diameter and 37 feet long. I spoke with my contact at Dutton-Lainson and he said that you could use a synthetic cable as long as it is rated high enough. The…

view full answer...

Answer 4

In terms of capacity, the Timbren Rear Suspension Enhancement System, #TGMRG25C, for a 2003 Chevy Avalanche 1500 has quite a bit more; a total capacity of 6,000 pounds. Compare that to the maximum 1,000 pound capacity of the Firestone Vehicle…

view full answer...

Answer 5

Both the Firestone #F4108 and Air Lift #AL60769 helper springs are confirmed to fit your Cadillac Escalade as long as you don't have the auto-leveling option. If your Caddy has the auto-leveling you'll need to go with the Firestone. There…

view full answer...

Answer 6

It is not recommended to use any type of suspension enhancement when using a weight distribution system. The two systems will work against each other and would provide an unsafe, unpredictable ride quality. Your best option would be to make sure the…

view full answer...

Answer 7

I spoke with my contact over at Timbren about helper springs #TGMRYS4. The overall height of the whole assembly is 4-3/4 inches. The spring by itself is 3-3/4 inches. You'll want an inch to an inch and a half of space between the frame/axle and…

view full answer...

Answer 8

For your 2018 Cadillac Escalade the Timbren Rear Suspension Enhancement System #TGMRYS4 will work great. These jounce-style springs are confirmed to fit your vehicle and will simply replace the factory bump stop on the frame to provide additional…

view full answer...

Answer 9

What I recommend is going with the Timbren vehicle suspension #TGMRYS4 (2WD or 4WD)because the hollow rubber springs sit above the axle and they are easy to install. It will also be compatible with your auto-leveling system. Also, the Timbren…

view full answer...

Answer 10

We sure do! For the rear axle of your 2018 Cadillac Escalade I recommend the Timbren Rear Suspension Enhancement System #TGMRYS4. These are confirmed to fit your vehicle and will simply replace the factory bump stops on the frame to provide…

view full answer...

Additional Tee Required To Use Firestone Coil-Rite Air Helper Springs With Single Schrader Valve

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching