Dimension of Redline Bolt-On Spring Latch # SL716

Question

Question:

What is the measurement from the bottom of the base up to the center of the pin?

asked by: Jim

0

Expert Reply:

The base of the # SL716 Spring latch to the center line of the pin measures exactly 13/16 of an inch, as you can see in the diagram I have edited for you.

expert reply by: Mike L

0

click to enlarge

Answer 1

I went out to the warehouse to measure the Bolt-On Zinc Spring Latch Item #SL716 for you. With the pin pulled all the way out (spring fully compressed) it measures approximately 4-7/8 inches from the outside of the bracket to the end of the loop.…

view full answer...

Answer 2

Thanks for the pictures of your horse trailer's rear door. The part #2212 will work as a replacement for the hinges that you have. We have spring latches too like the part #SL716SS as well but do not have door seals.

view full answer...

Answer 3

I went and pulled a Bolt-On Stainless Steel Spring Latch #SL716SS from our warehouse and measure the dimension you are looking for and found it to be 1-7/8 inches. See the pic I attached, I added the dimension to the picture you submitted

view full answer...

Answer 4

It's totally normal for a bit of movement between any fifth wheel hitch and the base rails. The feet on the hitch are typically a bit smaller than the slots they slide into for mounting otherwise you'd have a hard time getting your…

view full answer...

Answer 5

The B&W Companion OEM 5th Wheel Trailer Hitch #BWRVK3700 is perfectly compatible with cushioned pin boxes like your MORryde RP072-1621HD, so the clunking you're experiencing isn't related to the two components being incompatible. With…

view full answer...

Answer 6

In order to replace the Advent Analog Wall Thermostat ACTH11 you'll need the Air Distribution Box w/ Wall-Mounted Thermostat for Advent Air RV Air Conditioners part #ACRG15. This is a digital style replacement which is what you'll need since…

view full answer...

Answer 7

For a pair of stabilizer jacks that would have more than enough capacity that would work well on your R-Pod I would recommend the Stromberg Carlson Trailer Scissor Jacks part #JSC-24. These have a 5k capacity per jack and would do a great job as long…

view full answer...

Answer 8

Yes, you can replace your GE air conditoner with an Advent air conditioner like the Advent Air RV Air Conditioner #ACM150. Additionally, you will also need a thermostat. For that, you can use the Air Distribution Box w/ Built-In Thermostat for Advent…

view full answer...

Answer 9

The correct slide-out toppers for your 2021 Grand Design Reflection is the Solera RV Slide-Out Awning #LCV000177334 that will fit slide outs that are 140-145 inches wide and 48 inches long, and Solera RV Slide-Out Awning #LCV000168109 that fits slide…

view full answer...

Answer 10

Actually on brake magnets for trailers either wire can be used as the power or the ground so the colors don't really mean anything. Most likely the magnet manufacturer just put what ever color was most convenient on your trailer.

view full answer...

Answer 11

Most likely the new axle has self-adjusting brakes which when new are known for feeling pretty weak. The good news is that you can keep applying them over and over while the trailer is traveling and they will tighten and get more sensitive feeling.

view full answer...

Answer 12

I would check the magnets for wear before going on to test them with a meter. If the magnets show abnormal wear or if you can see the windings beginning to show through the friction surface of the magnet then they will need to be replaced. To further…

view full answer...

Dimension of Redline Bolt-On Spring Latch # SL716

Product Page this Question was Asked From

Continue Researching