Bike Rack Options for e-Bikes with Fenders and Carbon Frame Bikes

Question

Question:

I love the Kuat NV 2.0 for 4 bike option, but have one bike that is an electric with a front fender and at least one carbon bike that Id like to use a wheel mount with. Do you have a recommendation for the family with both fenders and carbon that would let you use some of each type of attachment frame and/or wheel?

asked by: Jamie F

1

Helpful Expert Reply:

The closest thing to match what you're looking for is the Inno Tire Hold Bike Rack for 4 Bikes # INH142. This uses hoops to hold both the front and rear tires and you can offset the bikes enough that you should be able to clear fenders on your bikes. The front 2 trays (nearest the vehicle) can each carry a 60 lb bike while the 2 rear trays can hold up to 40 lb bikes. Be mindful that the total weight capacity is 160 lbs so you can't load each try to capacity if you'll be carrying 4 bikes.

Another possible option is the Saris SuperClamp EX Bike Rack # SA4026F which has similar specs but it weighs in at 63 lbs which is a significant difference to the Inno Tire Hold weight of 118 lbs.

Aside from these options you would need to go with a frame mount rack like the Hollywood Racks Sport Rider SE # HR1400Z and then do your best to protect the frame of your carbon bike with something like the Thule Carbon Bike Frame Protector # TH984101.

Attached are some videos for you to check out.

expert reply by: Jon G

1

Answer 1

The Kuat Sherpa 2.0 #SH22G and the NV 2.0 #NV22G that you referenced are both excellent platform-style racks that will hold your bikes by the front wheels with no frame contact. These are top-of-the-line carriers and you really would not go wrong…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

There are some subtle difference between the Kuat Piston Pro Bike Rack for 2 Bikes #KU76ZR and the Kuat Piston Pro X Bike Rack for 2 Bikes #KU98VR. Overall the two racks are very similar, there are just some subtle differences/upgrades on the Piston…

view full answer...

Answer 6

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...