Front Air Bag Suspension Kit that Fits 2003 Workhorse RV Chassis

Question

Question:

I want to put air bags on 2003 workhorse front I beam suspension .is there a kit that will work.i can fabricate if necessary

asked by: Robert D

0

Expert Reply:

If your 2003 Workhorse RV is a P series P30 or P32 or the W18 series you'd want the Air Lift # AL81560.

expert reply by: Jameson C

0

Answer 1

The fittings on the bottom of the Air Lift bags like the part #AL81560 that you referenced do not have any type of valve in them so they can't be inflated directly. Basically it's a hollow fitting designed to have an air line slipped over.

view full answer...

Answer 2

For the front axle of your 2004 Workhorse P32 chassis the correct air bag kit is the Air Lift 1000 Air Helper Springs #AL81560. This includes both air springs and the hardware to install them. If you need just a single air bag by itself you can use…

view full answer...

Answer 3

Yes, since the Air Lift Compressor kit part #AL58WQ is a dual path compressor kit you could configure it the way you mentioned. You could run one path to the front bags and the other to the rear like you mentioned using tees.

view full answer...

Answer 4

The only option we carry for front suspension for your 2003 Winnebago Brave (Workhorse 32V) is the Air Lift 1000 Air Helper Springs for Coil Springs - Front #AL81560. The Air Lift 1000 provides 1,000 pounds of load-leveling capacity and has an…

view full answer...

Answer 5

Yes! Probably the single best addition you can make to provide better handling in your RV would be to install a rear anti-sway bar. Helper springs treat the symptom but not the cause like an anti-sway bar would. There are 2 rear sway bar options for…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Front Air Bag Suspension Kit that Fits 2003 Workhorse RV Chassis

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching