Are Different Sized Stake Pocket Inserts Needed For A 2016 Chevrolet Silverado 1500?

Question

Question:

I have a 2016 Silverado which has the odd shaped back two stack pockets. So if I’m ordering these stack plates#A70432 do the front and the back stack pockets get the same mounting plates or do I need to order 2 different sizes1 7/8” and 2”?

asked by: David

0

Expert Reply:

The Replacement Stake Pocket Insert for Adarac Custom Truck Bed Ladder Rack # A70432 should work for the front and the rear stake pockets on your 2016 Chevrolet Silverado 1500.

expert reply by: Bryce D

0

Answer 1

All you need to do is take a utility knife and cut the plastic covering the stake pocket out. Then you can use the Thule TracRac SR #TH43002XT-781.

view full answer...

Answer 2

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 3

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

The Reese Titan Extension/Reducer you referenced, part #RP45292 would work great with the 2-1/2 inch Class V hitch on your Ram. As you mentioned, the extension has a 8K capacity when cut down to the 24 inch length, that will provide a 2 inch receiver…

view full answer...

Answer 6

There is a Titan hitch extender that should work for you, but would require a Titan hitch be installed on your truck to handle a tongue weight loaded that far from the hitch. It is Reese part #RP45292. You can use it as a 34 inch extension or cut it…

view full answer...

Answer 7

You can use a 7-Way and 4-Way connector at the same time just as long as you are not overloading the light circuits. If your camper has a lot of outside lights like running lights, and brake/stop/turn lights then the lights that perform the same…

view full answer...

Answer 8

We have a full replacement for your light. The Command Electronics #CE86FR. Take a look at the attached video to see them in action.

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 11

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...