Thread Size Of Tightening Knob On Hi-Lift Jack Holder Brackets

Question

Question:

What size thread is the tightening knob? Can the stud Bolt? be changed to use with Yakima Lock Housing Y07220 which has 5/16-18 thread? Thanks

asked by: Ron M

0

Expert Reply:

The thread size of the tightening knob on The Hi-Lift Jack Holder Brackets for Rhino-Rack Pioneer Platform Rack - Top Mount # RR43219 is 1.5 mm.

The stud bolt can not be used with The Yakima Lock Housing # Y07220.

I attached a review video link below.

expert reply by: Noah E

0

Answer 1

The High Lift Jack Holder Brackets #RR43219 are compatible with industry-standard roof racks so they will fit just fine on the Thule Caprock Platform Truck Bed Rack for Crossbars #TH65YE.

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

There is a trailer hitch receiver as well as a 4-way wiring harness that fit your 2022 Jeep Grand Cherokee WL; that said, we don't have any way to reference a VIN so you'll need to confirm if you do have the WL, which is the new model of…

view full answer...

Answer 5

The dimension you are looking for on the #RR31102 is 1-1/2".

view full answer...

Answer 6

Rhino Rack offers the RT-Style Roof Rack Track that would mount directly to the roof of your 2008 Ford Ranger with pop rivets. You will need a rivet gun to install this track so if you do not have one already, you could purchase one from a local…

view full answer...

Answer 7

Yes, we do have foam pads that will fit around your Rhino-Rack Heavy-Duty Roof Rack Crossbars #RB1250 and allow you to carry your surf board. You can use the Rhino-Rack Crossbar Pads w/ Tie-Downs #RRRWP04. These pads will fit your HD crossbars. I…

view full answer...

Answer 8

The Rhino-Rack Heavy-Duty 50-Inch Roof Rack Crossbar #RB1250S has cross-section dimensions of 1-7/8-inches tall and 1-5/8-inches wide, as shown in the photo I prepared for you. We also offer two bars as a set #RB1250. The vehicle known as the…

view full answer...

Answer 9

Yes, the Batwing Awning #RR33100 (Driver's Side) or #RR33200 (Passenger's Side) can be mounted to your Yakima JetStream crossbars so long as they extend out past your roof rack's feet. They have mounting brackets which install inside the…

view full answer...

Answer 10

I measured the widths of the c-channel on the Rhino Rack Vortex Aero Crossbars and the bottom width is 7/8 inches and the neck width is 7/16 inches. I have attached a photo showing these measurements for you to check out. As long as the t-bolts on…

view full answer...

Answer 11

The Rhino-Rack CXB Leg Kit for Raised, Factory Roof Rack Side Rails #CXB will fit the factory rails on your 2022 Subaru Forester as long as those rails are not more than 1-1/2" tall and not more than 2-1/4" wide. This would allow you to use…

view full answer...

Answer 12

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Thread Size Of Tightening Knob On Hi-Lift Jack Holder Brackets

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching