Size of Redarc Tow Pro Elite Control Knob

Question

Question:

For 2018 Toyota Tacoma What is the size of this item RED78FR Height Width Depth, to include wire connection Size of required hole to be drilled in dash

asked by: Hugh M

0

Expert Reply:

We can for sure get you the dimensions of the control knob of the Redarc Tow-Pro Elite Trailer Brake Controller # RED44FR.

The knob of the # RED44FR requires 1-1/4" of depth, is 9/16" wide, and 3/4" tall; the size of the hole required is 25/64" per the linked instructions.

expert reply by: Kyle S

0

Answer 1

It sounds like the LED light has become damaged on your Redarc Tow-Pro Elite Trailer Brake Controller #RED44FR. First be sure to check the Redarc Tow-Pro Elite Control Knob Wiring Harness #RED26FR for any damage to the wiring or pins that would…

view full answer...

Answer 2

The V3 designation of the Redarc Tow Pro Elite part #RED44FR means that it's the most recent version of the brake controller. This is the third version and has been slightly updated. Functionally you wouldn't notice a difference aside…

view full answer...

Answer 3

I went to the warehouse to measure the Universal Mounting Panel for Redarc Tow-Pro Elite Trailer Brake Controller Control Knob #331-TPSI-001 and found the back was 1" x 1-1/2" and the widest point of the rear knob was…

view full answer...

Answer 4

I took a look at the online owner's manual of a 2016 Chevy Silverado 2500 and there was no listing of a trailer brake relay for this truck. The trailer brake fuse is fuse number 1 in the engine compartment fuse block so you may want to take…

view full answer...

Answer 5

Under the hood of your 2001 Chevy Silverado, remove the cover on the power distribution box. If standing in front of the truck facing the motor, the brake controller fuse will be that last large one in the back left corner, see picture. But the brake…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you don't have to worry about the water damaging wires like you would with electric brakes. That being said, if you use a heat shrink butt…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Answer 11

You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller #C24VV. The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever you like under…

view full answer...

Answer 12

I recommend the Redarc Tow-Pro Liberty Brake Controller #RED24FR for your 2023 Toyota Tacoma with the factory tow package. You will be able to connect the wiring using the Redarc Adapter #RED99FR directly to the factory connector. We also have the…

view full answer...

Size of Redarc Tow Pro Elite Control Knob

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching