Installing Brake Controller 2008 Honda Ridgeline Without Tow Package

Question

Question:

I am trying to install a prodigy p3 brake controller on my 2008 ridgeline. My ridgeline did not com with the tow package. I need help with connecting the wires to the battery and stoplight switch.

asked by: Mike S

0

Expert Reply:

When installing the 7-way trailer connector and brake controller, you will need to make two connections at the battery. The accessory circuit from the 7-way will run from the 7-way at the rear of the vehicle to the engine compartment, making sure to avoid anything hot or moving like exhaust and suspension or steering components. The wire would connect to an inline 40 amp circuit breaker, and then connect to the positive battery terminal. The power wire for the brake controller would pass through the firewall and also connect to the positive battery terminal via a 30 amp circuit breaker.

If you use our # ETBC7 Brake Controller Installation Kit, the trailer connector, all wiring, hardware, circuit breakers and hardware is included.

The red wire from the controller would connect to the brake stoplight switch. The switch is located at the top of the brake pedal, and will have numerous wires exiting it. Use a circuit tester like part # 40376 to test each wire. The circuit you are looking for will only show current on it when the brake pedal is pressed. Once located, tap the red brake controller wire into the circuit.

I have linked you to an installation video showing a brake controller being installed using our # ETBC7 kit. The video shows a controller being installed on a Honda Odyssey, but the procedure for your Ridgeline would be very similar. I have also linked you to an FAQ article showing how the installation kit is used.

expert reply by: Mike L

0

Answer 1

The Draw Tite hitch part #75280 is a fit for your 2006 Honda Ridgeline and is compatible with weight distribution. This hitch has higher towing capacities than the Curt so it would be what I would recommend. That being said this hitch (and all of our…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Travis, congrats on the new 2024 Jayco Flight 284BHS! Your travel trailer looks to have a GVWR of 7,950 lbs so I recommend going with the Equal-i-zer Weight Distribution w/ 4-Point Sway Control #EQ37121ET and pairing it with the Shank…

view full answer...

Answer 7

Hey Donald, the best Blue Ox weight distribution would be the pat #BXW0550 as it has a perfect tongue weight range for your 450 lb tongue weight trailer.

view full answer...

Answer 8

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. The Replacement Head for Blue Ox SwayPro Weight Distribution Systems part #BXW4011 is for…

view full answer...

Answer 9

It's very easy to install a trailer brake controller on a 2021 Honda Ridgeline. I recommend the Tekonsha Prodigy P3 Trailer Brake Controller part #90195 which comes with a harness that you could simply attach to the one that came with the…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...