Placement Of the Gear When Replacing A Lippert Electric Coach Step Module

Question

Question:

I replaced motor on my steps and forgot to note position of flat gear thats driven by the motor. Do you just center the gear or does it need to go with the stop fully to the right?

asked by: John R

0

Expert Reply:

While the steps are extended the flat gear should sit right at the stop on the right that you referenced (and is pictured below). As the steps close the gear will slide to the left, away from the stop and the control module # LC301702 in the picture.

expert reply by: Kevin C

0

Flat Gear Placement On Kwikee RV Steps
(click to enlarge)

Answer 1

Since you found the number 164889 that means the correct replacement module is the part #LC301702.

view full answer...

Answer 2

The issue you described sounds like a faulty control module. In order to replace this you will want to use the Replacement Control Module for Lippert Electric Coach Step part #LC301702 which is a direct fit for your Lippert Steps 128980. I spoke with…

view full answer...

Answer 3

The Replacement Control Module for Lippert Electric Coach Step #LC301702 has the purple wire that connects to the door light switch. The other end of the switch #LC301694 connects to the Replacement Wiring Harness for Lippert Electric Coach Step…

view full answer...

Answer 4

Per Lippert, the Replacement Control Module for Lippert Electric Coach Step. part #LC301702, will work for all Coach Steps. You should not have any problems. I have included a demo video below.

view full answer...

Answer 5

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 6

The spacing will depend on the axle diameter and on which particular spring hanger kit you use. If you have a 6000 lb 3 inch diameter axle, and you're using the #APT5 hanger kit which includes 7-3/4 inch equalizers and 2-5/8 inch shackle straps…

view full answer...

Answer 7

It's totally normal for a bit of movement between any fifth wheel hitch and the base rails. The feet on the hitch are typically a bit smaller than the slots they slide into for mounting otherwise you'd have a hard time getting your hitch in…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

On equalizer 013-105-04 in kit #K71-360-00 the eye center to eye center measurement is approximately 7-1/2 inches.

view full answer...

Answer 10

There is not a fuse we carry for the 8000 Series of Fan-Tastic vent. It does use a 4 amp slow blow fuse so to make fuse access simpler you can use In-Line Fuse Holder #C58470-1 and if you need to replace the bow-tie bracket, motor, and blade the…

view full answer...

Answer 11

All of the 2015 Honda Pilots would have a hitch installed on them from Honda. So that is one less piece of the puzzle that you would need. Since you wanted to do some towing you might be interested in etrailer ball mount kit #989900. It comes with 2…

view full answer...

Answer 12

It looks like all 2015 Honda Pilots come equipped with a hitch already (save for a select few). It's for that reason that none of our manufacturers made hitches for it, and why the 2016 hitches will not fit. In the middle of your back bumper, you…

view full answer...

Placement Of the Gear When Replacing A Lippert Electric Coach Step Module

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching