Correct Manual Adjust Dexter 3,500 lb Electric Brakes For Travel Trailer

Question

Question:

Would like to install parts for my 2006 trailer. casita 17ft deluxe freedom brake kit R&L want to order kits for this trailer please advise part number needed. The Dexter axle model is 10H, The weight capacity is 3500 lbs. I would like manual adjust, electric brake type. I don't know if this helps but Dexter part # for left is K23-026-00 and the right side is K23-027-00. Thank you for your help

asked by: Brian J

0

Answer 1

I don't know which specific 2006 Casita travel trailer you have, but if your Dexter axle is a 3,500 lb capacity axle then the brake kit part #23-468-469 that you referenced would be the correct kit. Typically you can find the axle capacity on a…

view full answer...

Answer 2

Yes, electric brakes like the #23-468-469 can be used on boat trailers that see salt water and fresh water. It's a smart idea to unplug the trailer wiring before backing the boat into the water but we realize most people do not do this. The part…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 8

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 9

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 10

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Answer 11

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 12

On Dexter 12" Nev-R-Adjust Electric Brake Assembly #23-458 the shoe pad thickness is 3/16 of an inch. Dexter says that you should replace the shoes if the material gets down to 1/16 of an inch thick or less.

view full answer...

Correct Manual Adjust Dexter 3,500 lb Electric Brakes For Travel Trailer

Product Page this Question was Asked From

Continue Researching