Running Boards and Rear Hitch Step for 2015 Mercedes Sprinter

Question

Question:

can you suggest side steps and a rear hitch step for my 2015 Spinter? thanks!!

asked by: MARIA H

0

Expert Reply:

For your 2015 Mercedes Sprinter we have the Aries Running Boards part # AA86ZB as a confirmed fit that would work well. Then for a wider rear step that was designed to fit a hitch we have the Westin HDX Drop Hitch Step part # W98TD.

expert reply by: Jameson C

0

Answer 1

There is a custom wedge you can use with a Sidewinder for your RBW Lil Rocker 5th wheel hitch. What you need is the following: - 5th Airborne Custom Wedge for RBW Fifth Wheels #SWW-07

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

For your 2022 Mercedes Sprinter 2500 that has a 170 inch wheelbase and the standard bumper the etrailer hitch part #e76AR is the highest capacity option available. It can tow a trailer up to 10,000 lb. We do not carry replacement leaf springs or step…

view full answer...

Answer 5

We do have replacement mounting hardware for the Aries Grille Guard on your 2008 Toyota 4Runner. If you have the #AA2058 the correct brackets and hardware are the #AABRKT-2058. If you have the #AA66XB then you need the #AABRKT-2066.

view full answer...

Answer 6

I recommend using the Curt Lock Set #C23556 for your Curt Adjustable 2-Ball Mount #C99NR. This comes with a lock for the hitch receiver and one for the ball mount platform. Even though your platform uses 2 pins, only 1 locking pin is needed to secure…

view full answer...

Answer 7

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 8

I was able to look up your previous purchase and it looks like you've ordered 2 different chain kits from us. I'll list them below along with the tire sizes they fit. If you let me know the year/make/model of your vehicle as well as the tire…

view full answer...

Answer 9

The Curt Adjustable 2-Ball Mount #C99NR uses Pins #C56NR which are 3/4" in diameter and have a usable length of 3-3/4". You will need the InfiniteRule Lock #IR36FR which is also 3/4" in diameter with a 3-7/8" span to lock the…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Running Boards and Rear Hitch Step for 2015 Mercedes Sprinter

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching