Do Spring Bars of Fastway FA92-00-0800 Weight Distribution Need to be Removed to Back Up Vehicle

Question

Question:

Do I have to remove the trunk on bars on this hitch before backing up in reverse? Thanks for any help

asked by: Ernest

0

Expert Reply:

If you're backing the vehicle at a tight enough angle that the trailer could possibly jackknife, it's recommended that the spring bars be removed. When you're backing a trailer at a sharp angle, it's easy to jackknife the trailer-and the shorter the trailer, the quicker it'll happen.

expert reply by: Mike L

0

Answer 1

Yes, the cam of the Reese Dual Cam III part #RP65FR has been upgraded from models that were made 20 years ago. The brackets have also been upgraded and made to be a lot easier to install as well.

view full answer...

Answer 2

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to RoadActive Suspension the spring rate for the standard kit #RAS3611-S is 2,400 lbs. For the heavy duty #RAS3611-SHD it is 3,600 lbs. The heavy duty #RAS3611-SLHD is the same but only designed to fit if you have factory top overload…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

I can definitely help and point you in the right direction. Both brands make a great quality air bag kit. Personally I prefer the Firestone Ride-Rite #F2709. The air bags themselves are known to be more durable than others. They can hold more PSI…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is comfortability when you…

view full answer...

Answer 10

For your 2015 GMC Sierra 3500 Denali DRW 4x4, I recommend using the Firestone Ride-Rite Red Label Extreme Duty Air Helper Springs part #F2709 over the Air Lift LoadLifter 7500 XL Air Helper Springs part #AL57538 for two reasons. The first reason is…

view full answer...

Answer 11

I highly recommend going with the Air Lift LoadLifter 5000 Air Helper Springs #AL49DQ over their Ride Control system for your 2023 Toyota Tacoma 4WD because they not only offer more support, but they also have a better construction so they'll…

view full answer...

Answer 12

Hey Donald, the best Blue Ox weight distribution would be the pat #BXW0550 as it has a perfect tongue weight range for your 450 lb tongue weight trailer.

view full answer...

Do Spring Bars of Fastway FA92-00-0800 Weight Distribution Need to be Removed to Back Up Vehicle

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching