Availability of Replacement Brake Assemblies for Lippert 4,400 lb Trailer Axles

Question

Question:

Hi, I have Lippert 4400 lbs axles labeled with manufacture date 09/05/2012, and they have attached brakes labeled Lippert 122258 and 122450 which are 3500 lbs brakes. The brake mounting hole pattern appears to measure a perfectly square 2-13/16 2.8 inches. My question is, what Dexter 4400 lbs. brakes will fit this pattern? Thanks for your help,

asked by: Dale H

0

Expert Reply:

The 4,400 lb trailer axle is an oddball when it comes to replacement parts but the easy solution is that you'd need 3,500 lb replacement assemblies like the part # AKEBRK-35-SA for a set of left and right hand assemblies that are self adjusting. While the assembly states that it was for a 3,500 lb trailer axle the great thing is that as long as the sizes and bolt pattern match up (like they do) they will work great. The only real difference between brake assembly capacities when the sizes are the same is a slight difference in magnet strength which can be compensated for with the brake controller.

expert reply by: Jameson C

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 3

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 4

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 5

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 8

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 11

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 12

On Dexter 12" Nev-R-Adjust Electric Brake Assembly #23-458 the shoe pad thickness is 3/16 of an inch. Dexter says that you should replace the shoes if the material gets down to 1/16 of an inch thick or less.

view full answer...

Availability of Replacement Brake Assemblies for Lippert 4,400 lb Trailer Axles

Product Page this Question was Asked From

Continue Researching