Replacement Dust Cap for Hub of Malone LowMax Trailer

Question

Question:

I need hub dust caps for my low max trailer. Which product do I need? Thanks,

asked by: Adam W

1

Helpful Expert Reply:

For the Malone LowMax trailer the correct replacement dust cap is the part # F001518.

expert reply by: Jameson C

1

Answer 1

Yes, the Malone EcoLight Sport Trailer - 58" Crossbars - 400 lbs #MAL53FR does have a zerk grease fitting on the hub. It is specifically on the back of the hub as you can see in the attached photo.

view full answer...

Answer 2

The Malone MicroSport trailers like you have use the bearing kit part #BK1-100 that you mentioned which comes with the correct seal size. Or for a replacement hub that comes pre-greased part #34822545BX. Then for a heavy duty and waterproof grease…

view full answer...

Answer 3

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 4

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 10

The inner diameters of the LM67048 and 15123 both are the same (1.250 inches). That means that a hub with either bearing in the outer bearing would fit your spindle. The part #AKHD-655-6-EZ-K would fit your axle.

view full answer...

Answer 11

You will need to measure the diameter of the spindles where the seal and bearings ride. Check out the picture I attached that shows where this is. You will need an exact measurement so either a digital or dial caliper will be needed. To pick out the…

view full answer...

Answer 12

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Replacement Dust Cap for Hub of Malone LowMax Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching