Surface Prep for Alpha Systems 4034 Roof Coating for RV Roofs

Question

Question:

Can this product be applied right from the container or do you have to apply a primer first?

asked by: Thom

1

Helpful Expert Reply:

The Alpha Systems 4034 Roof Coating for RV Roofs, # AL34CV applies with a brush or roller and adheres to polyurethane foam, aluminum, galvanized steel, fiberglass, cured concrete and EPDM roof membranes. The manufacturer does list requiring a primer to first be applied. But does state to ensure surface is clean, dry, and free of moisture or oils before application.

expert reply by: Michael R

1

Answer 1

The Alpha Systems 4034 Roof Coating for RV Roofs - 1 Gallon #AL34CV is designed to work with a variety of roof types including aluminum and galvanized steel. If this matches the metal you have then you're good to go! If you have a different…

view full answer...

Answer 2

Sounds like you may be looking for the Camco RV Vinyl Trim part #CAM25212 which is the plastic trim that goes around the outside of campers and inserts in a track. This is a black 100 foot long trim that's 1 inch wide. For white you'd…

view full answer...

Answer 3

The roof vent on your trailer is most likely for black water tank. The Lippert Components 360 Siphon RV Holding Tank Vent Cap part #LC389381 has a base with a 4" outer diameter. The holes most likely won't line up with your existing…

view full answer...

Answer 4

It sounds like you already have a 50 foot power cord for your RV to hook up to shore power, the Epicord RV Power Cord with Handle - 50 Amp Male to Twist Lock Female Connector - 50' Long #277-000157. There is a simple solution to this by…

view full answer...

Answer 5

Since you're adding more you'll want to wait for it fully cure and then wipe it down to ensure the surface is clean for the new sealant #AL98KV you'll be laying down to properly bond to the surface.

view full answer...

Answer 6

If the old sealant only has minor cracks you can use a sealant like the LaSalle Bristol XTRM Universal Self-Leveling Sealant #34427034145-1 which is a little easier to work with than the Alpha Systems 1021 Self-Leveling Sealant for RVs #AL98KV. You…

view full answer...

Answer 7

Hi Robert, So there isn't one that can be used with a cordless drill (which would be an electric jack only) as all the electric A-frame jacks are all higher than the 12" to 14" you want. There is a manual crank jack you can…

view full answer...

Answer 8

The rule of thumb here in most cases is, the smoother the surface and glossier the paint, the shorter the nap. With the roof of the trailer being fairly smooth a 3/4" or less nap would be the better option. The manufacturer recommends a…

view full answer...

Answer 9

The Global Link RV Entry Door Locking Latch Kit #GL55VR has the single latch with two different functions/modes. The upper keyhole locks the outside handle but still allows it to be opened from the inside for emergency exit. When you use the lower…

view full answer...

Answer 10

Are you only installing the #LC82FR (500731)? To replace your 500210 you will need the full kit #LC359259. There are also wiring changes you will have to make at the pump assembly before it will work. After speaking with Lippert it sounds like this…

view full answer...

Answer 11

You would need to reach out to Alfa to see what type of roof membrane they used on the trailer since there isn't a guide that would tell us what was used. Typically the roof membrane is either made of EPDM or TPO. The only roof coating we…

view full answer...

Answer 12

Sounds like you are looking for a lower profile jack for your trailer so that the tailgate of the vehicle does not interfere with it. I went to our warehouse and was able to locate an a-frame jack that measured less than 12 inches from the bracket…

view full answer...

Surface Prep for Alpha Systems 4034 Roof Coating for RV Roofs

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching