What Size Mast Does the Curt Replacement Long Arm Fit On

Question

Question:

What size tubing does the long arm slide on

asked by: Ben O

0

Expert Reply:

The Replacement Long Arm for Curt 2- or 4-Bike Platform Rack # C67HR is a replacement part for a Curt bike rack like the Curt 2 Bike Platform Rack # C18085. The Curt 2 Bike Platform Rack # C18085 has a mast (tube) measurement of 1-1/4" therefore the Replacement Long Arm for Curt 2- or 4-Bike Platform Rack # C67HR fits on a 1-1/4" mast (tube).

expert reply by: Scott S

0

Answer 1

Thanks for the picture! Based on the picture you sent you are correct you will need the Replacement Bike Arm - Long #C67HR to replace the broken arm on your Curt 2 Bike Rack #C18085.

view full answer...

Answer 2

I went out to our warehouse to take a look at the Hollywood Racks Replacement Frame Hook #HRBS-SPRFHLZ-L that you referenced. I found that the square opening on the base that's used to attach to the vertical post on the bike rack features inside…

view full answer...

Answer 3

Yes, the Replacement Short Hook "A" Assembly for Yakima TwoTimer and FourTimer Bike Racks - Qty 1 #8880524 is an OEM product. The Replacement Long Hook "A" Assembly for Yakima FourTimer Bike Racks - Qty 1 #Y77FR is the long hook…

view full answer...

Answer 4

Keystone Montana fifth wheel campers used a specific set of landing gear so the motor part #LC142178 so based on that the part #LC142178 is the correct replacement for it. The gear box is sold separately and for that you'd want the #LC276602.…

view full answer...

Answer 5

I'll start off by saying that the locks on the Curt Platform Bike racks like then #C18087 cannot be replaced, so the only way to be able to use the same key for all of the locks would be to replace all of the arms at the same time so they can be…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The Kuat Sherpa 2.0 #SH22G and the NV 2.0 #NV22G that you referenced are both excellent platform-style racks that will hold your bikes by the front wheels with no frame contact. These are top-of-the-line carriers and you really would not go wrong…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

What Size Mast Does the Curt Replacement Long Arm Fit On

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching