Will the Rhino-Rack Fairing for Pioneer Platforms Work with New Gen 56" Wide

Question

Question:

Will this fairing work with the newer gen Pioneer Platform? I have the 52112 in 36” x 56”.

asked by: Bill

1

Helpful Expert Reply:

The Rhino-Rack Fairing for Pioneer Platforms part # RR43251 is compatible with all gen Rhino-Rack Pioneer Platforms that are 56" wide so you will be good.

expert reply by: Conner L

1

Answer 1

According to iKamper's website, their product mounts to most cross bars due to its universal design, however since we do not carry their products I can not confirm this. With that being said, since they say it is universal, you can absolutely use…

view full answer...

Answer 2

The 60" x 56" Rhino-Rack Pioneer Platform #RR42113BF actually isn't designed to attach to roof rack crossbars, but instead mounts directly to a vehicle-specific fit kit. There isn't a separate kit available that would allow you to…

view full answer...

Answer 3

The Rhino-Rack Pioneer Platform System #RR93ZW comes with and uses the Rhino-Rack Backbone Mounting System that is custom fit for your 2018 Ford F-350 and mounts into the fixed mounting points on the roof of your truck. Since your truck has those…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Will the Rhino-Rack Fairing for Pioneer Platforms Work with New Gen 56" Wide

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching