Does the Lock N Roll Articulating Channel Tongue Trailer Coupler 336TS508 Fit a 3 Inch Tube

Question

Question:

Just to be clear, does the 336TS508 fit over 3 inch HSS tube?

asked by: Ron W

0

Expert Reply:

Yes, the Lock N Roll Articulating Channel Tongue Trailer Coupler - 3" Channel - Trailer Side # 336TS508 will fit. The channel width is 3" so it is designed to accommodate a 3" trailer tongue and can be bolted on or welded on for installation.

expert reply by: Robin H

0

Answer 1

The J-style kayak carrier I recommend that will work on square bars for your trailer is the etrailer J-Style Kayak Carrier #e98878. This will mount around your square bars that are up to up to 3-1/8 inches wide and 1-1/2 inches tall. This is a…

view full answer...

Answer 2

For your 6,000 lbs Dexter axles, the Dexter Electric Trailer Brake Kit w/ Parking Brakes - 12" - Left and Right Hand Assemblies - 6K, #23-112-113, will be the set of brakes for your trailer's rear axle. This kit will include both left and…

view full answer...

Answer 3

The Dexter Electric Trailer Brake Kit w/ Parking Brakes - 12" - Left and Right Hand Assemblies - 6K #23-112-113 does use a cam action lever like what you stated, but they will be compatible with your current cable system. You will simply remove…

view full answer...

Answer 4

The Demco Trailer Coupler #DM12688-95 does install to a channel bracket using bolts like what we find in the Kit #DM6166. If you were looking for a bolt-on channel bracket then the part #DM13867-52 would be what you're looking for which fits…

view full answer...

Answer 5

Thanks for the picture! I reached out to Dexter with your information and you have a 5,200lb #11 torflex axle and you'll need the following parts: (2) Brakes with Parking Brakes #23-112-113 (2) Brakes without Parking Brakes #23-105-106 (4)…

view full answer...

Answer 6

I will need to know more about the brakes currently on your trailer. First, measure the inside diameter and width of one of the hub and drum assemblies. The width is the just the width where the brake shoe pad makes contact with the inside of the…

view full answer...

Answer 7

Based on my research your M1101 trailer has a GVWR of around 3400lbs, so for a replacement axle I recommend taking a look at the Timbren Heavy-Duty Axle-Less Trailer Suspension - Straight Spindle - Off-Road Tires - 3,500 lbs #ASR35HDS01 which will…

view full answer...

Answer 8

On each individual electric brake magnet the amperage draw would be 3.0 to 3.2 max amps at 12 to 13 volts on 7-inch brake magnets and 3.2 to 4.0 max amps at 12 to 13 volts on 10 and 12-inch brake magnets. The max amperage draw for the brake magnets…

view full answer...

Answer 9

Since the trailer has 12 by 2 inch hubs the Dexter Axle brake assemblies, part #23-112-113, will fit just fine. They're rated up to 6,000 pounds as a maximum but a 5,200 pound axle uses the same size brakes, generally. I've linked a video on…

view full answer...

Answer 10

For you 5,200 lbs axles you can use the Electric Trailer Brake Kit - Self-Adjusting - 12" - Left and Right Hand Assemblies - 5.2K to 7K #AKEBRK-7-SA. This is a favorite assembly because after the initial setup, the assemblies will automatically…

view full answer...

Answer 11

I was unable to find specs on your trailer, so we will need to find this information on our own. To determine which bearings and seals you need, the best way to get that information is to take apart your current hub and inspect the numbers that are…

view full answer...

Answer 12

Electric brakes, like the Dexter Nev-R-Adjust Electric Trailer Brake Assembly #23-458 that you referenced, are actually becoming more and more common on boat trailers. They used to not be so common because water and electricity don't play nice…

view full answer...

Does the Lock N Roll Articulating Channel Tongue Trailer Coupler 336TS508 Fit a 3 Inch Tube

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching