Availability of Replacement Keys for 2003 Fleetwood Wilderness Yukon Travel Trailer

Question

Question:

I have a 2003 fleetwood wilderness Yukon travel trailer but the keys were stolen and it was my only set . Do you know the best way to get replacement?

asked by: Craig F

0

Expert Reply:

In order to replace the keys for your 2003 Fleetwood Wilderness Yukon Travel Trailer you will need to replace the locks. To find a door lock that fits you will need to have the current lock removed and measure the cutout hole. For example, if the cutout measures 2-3/4" wide x 3-3/4" tall then you could use the Bauer Products Camper Door Lock # BA54FR.

I have included a link to all of our RV replacement locks that you can check out.

expert reply by: Robin H

0

Answer 1

The lock code could be located on the key itself, on the face of the lock core, or one a sticker attached to the lock (see photos). Once you find this you can then order the correct replacement key assuming you have a Global Link, Fastec (FIC),…

view full answer...

Answer 2

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 3

Possibly; you'll need to take some measurements as there are no specific door locks and handles for any specific RV. So measure the door thickness and cut out. For example, if you have a door that is 1-1/4" to 1-1/2" thick and a cutout…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Answer 7

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 8

We recommended to repack the wheel bearings on your trailer every 12 months or 12,000 miles. There is not a specific guideline as far as actually replacing the bearings. When repacking them with grease, you will also just want to check for any damage…

view full answer...

Answer 9

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 10

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 11

The absolute best cushioned equalizer that fits the dimensions you mentioned having would be the MORryde ALLTREK 4000 part #MR89DR as this is only option to provide vertical and horizontal cushioning. This would make a big difference and you'd be…

view full answer...

Answer 12

Hey Doug, thanks for reaching out! The MORryde ALLTREK 4000 #MR89DR dimensions can be a bit difficult to explain via text so I've attached an image giving you the dimensions you're asking about!

view full answer...