What Is The Difference Between The B&W 1067 And 1067R Turnover Ball Gooseneck Trailer Hitch

Question

Question:

Is there any difference in a BandW 1067 and a BandW 1067R?

asked by: Dana W

0

Expert Reply:

I contacted the B&W representative and he said there is not a difference between the B&W 1067 and 1067R, the R stands for revision. So the B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs, part # BWGNRK1067, is the revised version.

I have included a video demo link below.

expert reply by: Mark Smith

0

Answer 1

Wheel #AM20789 is the Dexstar wheel you are looking for. The 17-310 is the Dexstar part number. The only difference is that we use a different part number #AM20789. It is the exact same wheel made by Dexstar: 16x6 with 8 on 6-1/2 bolt pattern rated…

view full answer...

Answer 2

A goose neck hitch ball, or the center of a 5th wheel hitch head for that matter, will be located either right over the rear axle or an inch or so forward of it. You do not want a goose neck hitch ball to be located behind the rear axle since this…

view full answer...

Answer 3

Yes, both special trailer (ST) and light truck (LT) tires can be used on a 5th wheel trailer. They are actually the only two types of tires rated for this use. The reason for this is that tires on a trailer will be subjected to much harsher…

view full answer...

Answer 4

You can definitely connect a 5th wheel wiring harness to the bumper 7-way on your truck. The second in-bed 7-way connection is simply to give an easy access point and clean look. It keeps the wiring from dragging or moving against your tailgate, so…

view full answer...

Answer 5

Stander pin size for 5th wheel trailer hitches that install in the industry standard above the bed rails, such as those included with Husky kit #HT31404-686, are 1/2 inch in diameter and 3-1/4 inches long like #6014. A longer pin could be used but…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 11

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

What Is The Difference Between The B&W 1067 And 1067R Turnover Ball Gooseneck Trailer Hitch

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching