Is There a Replacement Lid For The Curt Hitch Sensor For MultiPro/Multi-Flex Tailgates?

Question

Question:

Can I purchase just the hitchcap for the 2 1/2 curt multipro tailgate sensor?

asked by: Roland R

0

Expert Reply:

Currently the 2" Hitch Cap Sensor # C56UR and 2-1/2" Hitch Cap Sensor # C36UR for GMC Sierra MultiPro and Chevy Silverado Multi-Flex Tailgates do not have any available replacement parts. You will need to get the entire kit to replace the sensor cap on your 2021 GMC Sierra 3500.

expert reply by: Bud M

0

Answer 1

I definitely recommend adjusting your 2022 GMC Sierra 3500 back to the factory settings and then potentially removing the Edge Pulsar V3 L5P Inline Tuner #EP82AR prior to taking it in to a dealer for service. I'm not sure if it will do…

view full answer...

Answer 2

Yes we do have exactly what you're looking for! The 5th-Wheel-to-Gooseneck Coupler Adapter Mounting Plate for MORryde Pin Boxes #MR37ZR is the MORryde RPB77-006 adapter that you're looking for.

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to…

view full answer...

Answer 5

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 6

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 7

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 8

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 12

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Is There a Replacement Lid For The Curt Hitch Sensor For MultiPro/Multi-Flex Tailgates?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching