What is Quietest Electric A-Frame Trailer Jack

Question

Question:

Im looking for the quietest jack? Any suggestions?

asked by: Tim F

0

Expert Reply:

We've found that the Bulldog trailer jacks like the part # # BD500199 (Black) or # BD500200 (White) are the quietest so either of these would be your best option.

expert reply by: Jameson C

0

Answer 1

For your Bulldog Electric camper jack #BD500200 will run just fine off of any 12V battery. Often the trailers that use these jacks will have other components they will run as well like lighting, vent fans, etc so it is recommended to use a deep…

view full answer...

Answer 2

You can use the Replacement Tongue Jack for Lippert Ground Control TT Leveling System #LC421366 as a jack and it sounds like you might be testing the function without it attached to the trailer, which is why it's not working. This unit does…

view full answer...

Answer 3

The trailer jack should very much NOT be powered by the breakaway battery. That was likely done by the previous owner for convenience. The breakaway battery is a dedicated battery for the breakaway system only. It needs to be able to apply the…

view full answer...

Answer 4

I checked and found the manual for the Lippert Electric Trailer Jack #LC285318 and there was no mention of anything going in the hole beforehand to tighten them. I added a cut out of the manual for you which shows the parts for this jack, and it does…

view full answer...

Answer 5

There are pros and cons to both Husky and Bulldog electric trailer jacks. My favorite Husky jack is the Husky Brute Electric Trailer Jack part #HT87247 and my favorite Bulldog jack is the Bulldog Powered-Drive Trailer Jack part #BD500187. The reason…

view full answer...

Answer 6

There are some Dutton-Lainson trailer jacks that are made in the USA as well as a few that are not. Any jacks that we carry that are made in the USA have that as part of the description to help set them apart. Currently we have the following options:…

view full answer...

Answer 7

The Bulldog Powered-Drive Trailer Jack, item #BD500200, only has one wire, the power wire. This jack attaches to ground through the mounting hardware and the trailer frame. When wiring the jack to your 7-Way trailer connector you will need to make…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

What is Quietest Electric A-Frame Trailer Jack

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching