Trailer Hitch Receiver Fit For 2011 Toyota Camry SE
Question:
Hi there. I am looking for a class 2 rear trailer hitch for a 2011 Toyota Camry SE. I found a couple options on the e-trailer site but wasnt sure which if any would fit the SE model? Could you suggest something that would fit my needs or if there is nothing that fits my make and model could an auto shop do any modifications on my vehicle to get something to fit? Thanks
asked by: Ryan D
Expert Reply:
There is indeed a fit for a trailer hitch receiver for your 2011 Toyota Camry SE from Draw-Tite, and it is a Class II hitch with a 1-1/4 inch receiver. The correct part number is the following:
- Draw-Tite Trailer Hitch Receiver # 36416
I verified with the manufacturer for you that the # 36416 is a fit for your '11 Camry SE. I also wanted to mention, if you plan on doing some light towing with your Camry, you'll also need trailer wiring, a ball mount, and a hitch ball, which you can get with the following parts:
- T-One Vehicle Wiring Harness # 118482
- Draw-Tite Drawbar # 36061
- 2" Hitch Ball # 19258 or 1-7/8" Hitch Ball # 19257
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 2-3/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-3/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class II
- 300 lbs TW
- 3500 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-3/4" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Rise - 3 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: How to Measure for Trailer Hitch Drop
- Article: My Trailer Hitch Doesn't Fit
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Q&A: Trailer Hitch and Wiring Recommendation for 2018 Ford Focus ST Hatchback
- Article: Trailer Wiring Diagrams
- Article: How to Choose a Cargo Carrier That Will Clear a Rear Mounted Spare Tire or Bumper
- Q&A: What Kind of Hardware Should I Use For My Trailer D-Ring Tie Downs?
- Q&A: Locating Factory Weldnuts on 2003 Volvo V70 to Install Curt Trailer Hitch # C12318
- Q&A: Can Trailer Hitch Extender hes0 Be Used for Towing with a 2007 Ford Explorer
- Q&A: Will the Wiring Harness # C59496 Fit on a 2006 Volvo XC70
- Q&A: Trailer Hitch for a 1997 Toyota Camry LE