Can Mount-n-Lock GennyGo Generator Carrier Fit Where There's 2 inches Between Bumper and Trailer

Question

Question:

Hello I have an all aluminum Camp Lite Trailer. It has a 2 in by 4 in Aluminum Bumper with a 2 in gap between the trailer and the bumper. Can this unit be mounted to my bumper to support 100 lb generator?

asked by: Bill H

0

Expert Reply:

Yes the Mount-n-Lock GennyGo Generator and Cargo Carrier for RV Bumpers # MNT77FR that you referenced would fit on a trailer that has only 2 inches between the rear bumper and body of the trailer.

expert reply by: Jameson C

0

Answer 1

The Go Power Solar Flex Eclipse Charging System w/ MPPT Solar Controller and 190 Watt Solar Panel #GP67MR is perfectly safe to install directly on your RV roof. You're correct that the flat "fixed" solar panels are designed to have some…

view full answer...

Answer 2

We do have the panels separately. What you're looking for is the Go Power Overlander Expansion Kit - 200 Watt Solar Panel #34282182.

view full answer...

Answer 3

Hey Don; good question and no other parts - including any type of adapter plate or mounting plate - is needed to mount the 30 Amp Go Power PWM Solar Charge Controller with Bluetooth #GP76QR. The #GP76QR comes with screws and is ready to be mounted…

view full answer...

Answer 4

Thanks for reaching out, Michael! The Dexter Electric Trailer Brakes #K23-086-087-00 are compatible with 3,500 lb axles and have the standard 4-bolt pattern so if that matches the specs of your axle then this will definitely work for your…

view full answer...

Answer 5

The mounting holes are 16-1/4 inches apart on the Curt hitch, part #C15845. Also the rivet holes are 3 inches apart. I've included the diagrams of all the mounting hole measurements for you. As well as the install details of the hitch.

view full answer...

Answer 6

Yes, if you plan on bolting the Stromberg Carlson Adjustable Accessory Hitch Receiver #SC45MR on then you would need to drill holes in the adjustable arms in order to set them to the correct length. There aren't any predrilled so that this one…

view full answer...

Answer 7

For your 2014 Mercedes Benz GL450 you'd need to use a set of universal mirrors since there aren't any custom ones made to fit your vehicle. For that we have the Dual View K-Source mirrors part #KS3990 which we have found fit really well, are…

view full answer...

Answer 8

I would be happy to help! The Curt Trailer Hitch Receiver #C15845 you were looking at is designed to fit the 2003 Ford F-350/450/550 Cab and Chassis motorhomes, and will not work on your 2003 Thor Four Winds Hurricane built on the Ford F53 chassis.…

view full answer...

Answer 9

Yes, The Curt Class V Trailer Hitch Receiver part #C15845 will fit all models of the 2019 Ford F-550 Cab and Chassis with 34" wide frames outside to outside.

view full answer...

Answer 10

The Roadmaster Htich Extender #RM-071-1075 measures approximately 3 inches deep from the pin hole to the furthest point inside the receiver tube. It's also only designed to be used to flat tow a vehicle with a hitch style tow bar. It can't be…

view full answer...

Answer 11

If you are needing to extend the gap between your tow vehicle and trailer, the Roadmaster Anti-Rattle hitch Extender #RM-071-1075 referenced in your question will provide a great solution. This is compatible with any 2 inch hitch receiver and will…

view full answer...

Can Mount-n-Lock GennyGo Generator Carrier Fit Where There's 2 inches Between Bumper and Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching