Replacement Jack For Fulton Magnum Series Pipe Mount Sidewind Jack
Question:
I need to replace my trailer jack as you can see in the photo its bent but its also hooked up quite uniquely to my trailer. Do you have this exact trailer jack that I can simply replace?
asked by: Teddy P
Expert Reply:
I recommend the Bulldog Round, Pipe-Mount Swivel Jack # BD1541150301 to replace the Fulton jack currently on your trailer. The Bulldog jack uses the same Pipe Mount connection so that you can easily replace your jack. The jack is rated for 2,000lbs and has 10" lift height.
Since you have a wheel you will also need the Replacement 6" Caster Wheel # BD500245 to attach to the jack. The caster is rated for only 1,200lbs so you will need to ensure that you do not exceed that with the caster attached.
(click to enlarge)
(click to enlarge)
Products Referenced in This Question
Replacement 6" Caster Wheel for Bulldog Trailer Jack with 2" Tube Diameter - Qty 1
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Jack Wheel
- 6 Inch Wheel
- Wheel w Caster Assembly
- Bulldog
more information >
Product Page this Question was Asked From
Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 10" Lift - 2,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 1001 - 2000 lbs
- Sidewind Jack
- Swivel Jack
- 10 Inch Lift
- Pipe Mount
- Weld-On
- No Wheel or Foot
- Bulldog
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Wiring
- Shop: Round, Pipe Mount Swivel Jack w/ Footplate - Weld On - Sidewind - 10" Travel - 3,000 lbs
- Video: Redline Plastic Stem and Rubber Socket Door Holder Installation
- Video: Redline Enclosed Trailer Parts - Doors - DH39R Review
- Shop: Floor Mats
- Q&A: Is a Wheel Available for a Pipe-Mount Swivel Trailer Jack
- Shop: B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs
- Q&A: Wiring Diagram for 7-Way Round Pin Trailer and Vehicle Side Connectors
- Search Results: 158151
- Search Results: bd1541150301
- Search Results: 15000
- Search Results: bd015279
- Shop: Bulldog Round Jack without mount - Sidewind - 10" Lift - 2,000 lbs
- Shop: Pipe Mount Swivel Style Trailer Jack with Foot - Topwind - 10" Travel - 2,000 lbs.
- Shop: Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Pole Connector - 7' Long
- Search Results: door cable
- Search Results: door holder
- Shop: Replacement U-Bolt for 2" Wide, Square Axles - 1/2" Diameter - Zinc Plated
- Shop: Low-Profile Bumper Door Holder for RV or Enclosed Trailer - 1" Stem
- Search Results: coupler
- Shop: Brake Controller
- Article: Pintle-Hitches
- Q&A: Where Does Brake Controller Install 2018 GMC Sierra
- Q&A: Recommended Tuner for 2018 Ford F-150 with 5.0L Engine
- Q&A: How to Determine if Dexter Tandem-Axle Trailer Hanger Kit for 2-1/2 Slipper Springs Will Work
- Article: How to Install a Brake Controller on Chevrolet / GMC 1999-2006 Pickups
- Q&A: Do Topwind A-Frame Jacks Use The Same Gears As Sidewind Jacks
- Q&A: Can The Foot Plate On The Round, Pipe Mount Swivel Jack # TJP-5002S-B Be Changed To a Wheel?
- Article: Gooseneck Trailer Hitch Information and Review
- Article: Wiring Trailer Lights with a 6-Way Plug (It's Easier Than You Think)