Diameter of the Axle Brake Grommet 046-016-00

Question

Question:

Can you tell me what the tube OD is of this grommet? Basically what size hole in the axle does the grommet require for ion. I have a AL-KO 3500# axle with a 3/8inch hole. Thanks for all info.

asked by: William G

0

Expert Reply:

The diameter of the Replacement Brake Wire Grommet # 046-016-00 is 3/8" with a length of 7/16". I have attached a video that goes over these measurements at the 25 second mark of the video.

expert reply by: Scott S

0

Answer 1

Dexter has confirmed that the #046-124-00 snap in grommet will work with their 7K axles.

view full answer...

Answer 2

Yes, you can use 10 Gauge Wire #10-1-1 to route through your axles to power your Electric Brakes #K23-478-00 Do be sure the Grommet #046-124-00 is in place on your axle tube to prevent the wire from fraying entering the axle tube.

view full answer...

Answer 3

As with any other item on a trailer, such as tires, wheels, winches or jacks, when selecting safety chains you want to ensure a good safety margin, in other words, you want to use an item that has a good bit more capacity than you will actually need.…

view full answer...

Answer 4

Safety chains are required by law in many different places, and in order to find out about the specific regulations you will need to contact your local DMV. I will say that no matter what the law may be, safety chains are a very good idea, no matter…

view full answer...

Answer 5

I definitely understand how safety chain capacities and determining exactly what chain rating you need for your trailer can be a bit confusing. To keep it as simple as possible, safety chain requirements state that the breaking strength of EACH…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Diameter of the Axle Brake Grommet 046-016-00

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching