Distance From End of TruRyde #84 Spindle Stub to the Back of an Installed Hub
Question:
The back meaning the back of the idler hub where the studs are attached, not where the tapered hub first starts at the end of the stub. Hub part AKIHUB-545-35-K. I want to use these trailer spindles for a walking beam suspension but I need this measurement from stub end to the back of the hub, for getting the wheel offset correct. Thank You....... David
asked by: David H
Helpful Expert Reply:
When installing a hub like the # AKIHUB-545-35-K on the # TRU84FR the hub is going to stop where the grease seal sits. If you look at the attached picture below, you will see the measurement marked F which is 6-1/2". This would be the stub length, which is the same as the distance from the end to the back of the hub. If you are talking about the other end, the distance would be the overall spindle length of 11-1/4" minus F, which would be 4-3/4".
Products Referenced in This Question
#84 Spindle for 3,500-lb Trailer Axles - 1-3/4" Diameter
- Trailer Spindles
- Standard Spindle
- 1-3/4 Inch Diameter
- Round
- For 3500 lb Axle
- TruRyde
more information >
Product Page this Question was Asked From
Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-1/2 - Pre-Greased
- Trailer Hubs and Drums
- Hub
- Pre-Greased
- Standard
- L68149
- L44649
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Continue Researching
- Shop: Dexter Nev-R-Adjust Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3.5K
- Shop: #84 Spindle for 3,500-lb Trailer Axles - 1-3/4" Diameter
- Shop: #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axle - 1-3/4" Diameter
- Shop: Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-1/2 - Pre-Greased
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Galvanized
- Shop: #84 Spindle for 3,500-lb Trailer Axles - 1-3/4" Diameter
- Q&A: Correct Hubs for Boat Trailer with L68149 and L44649 Bearings
- Shop: 4-Leaf Double-Eye Spring for 2,000-lb Trailer Axles - 26" Long
- Video: etrailer Trailer Idler Hub Assembly Installation
- Search Results: hub assembly
- Search Results: akihub~545~35~k
- Video: Review of TruRyde Trailer Spindles - EZ Lube Spindle - TRU74FR
- Video: Kenda Tires and Wheels - Tire with Wheel - AM32424 Review
- Q&A: How to Determine Wheel Offset of Trailer Wheels
- Q&A: Replacement Axle for a 1991 Lowe Boat Trailer
- Q&A: Selecting New 5-Bolt Hubs to Replace Original 4-Bolt Hubs on 1970's Dexter 3500-lb Axles
- Video: Review of CE Smith Trailer Fenders - No Step - CE18041ATB
- Video: Dutton-Lainson Trailer Winch - Brake Hand Winch - DL10970 Review
- Video: Review of Dexter Trailer Brakes - Electric Drum Brakes - K23-478-479
- Shop: Mud Flaps
- Q&A: What is the Difference Between Load Range C and D ST175/80D13 Trailer Tires
- Q&A: Replacing Damaged Axles and Spindles on a Yacht Club Trailer
- Search Results: mud flap
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Video: Review of Bulldog Winch Electric Winch - Hoist Winch - BDW64FR
- Search Results: strap
- Search Results: e98840
- Search Results: c56291
- Q&A: Determining Which Hub Replaces Dexter 8-243 Clamp On Wheel Hub
David H.
1/4/2022
The back meaning the back of the idler hub where the studs are attached, not where the tapered hub first starts at the end of the stub. Hub part AKIHUB-545-35-K. I want to use these trailer spindles for a walking beam suspension but I need this measurement from stub end to the back of the hub, for getting the wheel offset correct. Thank You....... David