What is the Right Drum Brake Assembly that Goes with the Left Assembly # K23-171-00?

Question

Question:

what is the right hand assembly like the K23-171-00?

asked by: Marianne

0

Expert Reply:

The correct corresponding right hand assembly for the Dexter Hydraulic Drum Brake Kit # K23-171-00 is the # K23-172-00. We also sell both of these parts together with the # 23-402-403.

expert reply by: Bob C

0

Answer 1

To get the correct replacement brake drums for your 8,000 pound axles, you will need a few things to be verified. The first will be if they are are hydraulic or electric brakes. If they are hydraulic, we currently have the Dexter Hydraulic Drum Brake…

view full answer...

Answer 2

It sounds like you have the Dexter Hydraulic Drum Brake Kit #23-402-403 on your Dexter P15 8,000lb axle. The Arm on the Dexter Hydraulic Drum Brake Left #K23-171-00 and Right #K23-172-00 is for a parking brake feature. While you will be able to fit…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 8

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Answer 12

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

What is the Right Drum Brake Assembly that Goes with the Left Assembly # K23-171-00?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching